User manual BOSCH SGV 5603-03

[. . . ] Before using your appliance for the first time . . en Safety instructions Delivery Immediately check the packaging and dishwasher for any damage which may have been caused in transit. Do not use a damaged appliance, but consult your supplier. Please dispose of packaging material properly. [. . . ] Note If you use the detergent and rinse aid separately or switch from combined detergents to standard cleaning products, ensure that the rinse aid dispenser amount has been switched on and the water softening system has been set to the correct water hardness or to "hardness auto". Switching "Add rinse aid" off and on: Switch on the appliance with the main switch 1 . Keep pressing button M/OK 2 until the "rinse aid 4" setting is displayed. By pressing buttons ­ or + 3 , you can select a set value between 0 and 6. To switch off, select position "0" Press button M/OK 2 . The set value is saved and you are returned to the Start menu. If the set value "0" is selected, rinse aid is not dispensed. Low rinse aid is not displayed. 20 en Programme overview Type of utensil e. g. Type of food remains e. g. Hardwearing Mixed Fragile Mixed Soups, soufflés, sauces, potatoes, pastries, rice, eggs, fried food Soups, potatoes, pastries, rice, eggs, fried food Coffee, cake, milk, sausage, cold drinks, salads Rinse if the utensils have been left for several days prior to washing in the dish washer Amount of food remains Condition of food remains Very adhesive Large -> small Slightly adhesive Very small Wash programme AUTO SUPER WASH 60° ­ 70° AUTO WASH 45° ­ 55° AUTO DELICATE WASH 35° ­ 45° QUICK WASH 45° PRERINSE ONLY Programme progress Prerinse The programme progress is optimised and adjusted according to the appliance load and degree of soiling on the utensils. Clean Intermediate wash Final wash Drying 21 en Programme data The programme data (duration, energy and water consumption) can be found in the summary of instructions and refers to standard conditions. Greater deviations may be caused by: different quantities of utensils inlet temperature of the water water pressure ambient temperature mains voltage tolerances and appliance-specific tolerances (e. g. temperature, water flow rate, etc. ) Only ranges can be indicated for the automatic programmes. Change this setting only if there are streaks (reduce the value) or water stains (increase the value) remaining on the dishes. You can choose a value between 0 and 6. Language You can change the language selected when the appliance was started for the first time (see chapter "Before Starting The Device For The First Time"). If the option "Language" is chosen the display shows several language abbreviations. The abbreviation of the currently selected language is flashing. In order to choose a different language, press ­ or + 3 until the desired language appears. Confirm the language selection by pressing M/OK 2 . All subsequent optical character messages will be displayed in the selected language. Water Hardness The factory setting "Hardness-Auto" allows the deposit sensor to determine the hardness and to control the softening system automatically. This means that changes to the settings are unnecessary during start-up or in case of changes in the water hardness. 24 en Standard Programmes In addition to the rinse programmes available in the Main Menu you can choose among the following standard programmes from the programme "Normal": Extra, Eco, Normal, Plus. Set the desired programme and start the selected programme by pressing the Start Button 5 . If you do not want to use any of the displayed standard programmes return to the Main Menu by using the button M/OK 2 . If you want to cancel the selection of a standard programme in the Main Menu press the button ­ "Back". [. . . ] If the water pressure is higher, install a pressure reducing valve. Flow rate: Minimum of 10 litres per minute. Water temperature: We recommend that you use cold water. If you do use hot water, the temperature should not exceed 60 °C. Removing the appliance It is essential, when removing the appliance, to observe the following sequence: First, disconnect the appliance from the power supply. [. . . ]