User manual BOSCH SMI 63M52EU/81 SUPPLEMENT
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual BOSCH SMI 63M52EU/81. We hope that this BOSCH SMI 63M52EU/81 user guide will be useful to you.
Lastmanuals help download the user guide BOSCH SMI 63M52EU/81.
Manual abstract: user guide BOSCH SMI 63M52EU/81SUPPLEMENT
Detailed instructions for use are in the User's Guide.
[. . . ] This warranty gives you specific legal rights, and you may have other rights which vary from state to state. Sears, Roebuck and Co. , D/817 WA, Hoffman Estates, IL 60179
If you want your water softener professionally installed, talk to your Sears Salesman. He will arrange for a prompt, quality installation by Sears Authorized Installers.
SEARS INSTALLATION POLICY All installation labor arranged by Sears shall be performed in a neat, workmanlike manner in accordance with generally accepted trade practices. Further, all installations shall comply with all local laws, codes, regulations, and ordinances. [. . . ] It works toward providing you with soft water for the longest time and the most efficient salt usage. Softening capacity is used as hard water goes through the softener and hardness minerals are removed, capacity is used. When the computer determines that only enough capacity remains to provide soft water up to the next regeneration starting time (2:00 AM, or as otherwise set) it will schedule a regeneration. When the regeneration begins, TONIGHT goes off and *RE CHARGE or RECHARGE TIME REMAINING flashes during the 2 hour regeneration. *NOTE: If the CLEAN feature is set to ON, a cleaning backwash (CLEAN and Bkwsh or Rinse flashes in the display, along with the minutes of the clean cycle remaining), precedes the recharge.
AUTOMATIC BYPASS During the brining, brine rinse and backwash cycles of regeneration, hard water goes through the softener valve and to the house pipes. However, you should not use HOT water, if possible, because the water heater will refill with hard water. The softener regenerates from 2:00 AM to about 4:00 AM, (you can set anytime), a time when not much water is used.
If you get up early in the morning and you can hear the softener regenerating, change the time setting. Then regeneration will start and end that much earlier and your water heater will not refill with hard water if a hot faucet is opened.
CARE OF YOUR SOFTENER
SALT. . . REFILLING STORAGE TANK/BREAKING A SALT BRIDGE
all the salt before refilling. Without salt, you will soon have hard water.
WHEN TO REFILL WITH SALT
The Salt Monitor System (see page 10) will turn on the low salt light to warn you when to refill with salt. Check for a low salt light a few weeks after you install the softener, and every week after that. Never let the softener use
You will have a loss in softening capacity and may get partly hard water if less than 10 inches (salt monitor level 2) of salt is in the storage tank.
PLEASE SEE PAGE 9 FOR SALT FILLING DIRECTIONS. Printed instructions are on the resin bed cleaner bottle.
CARE OF YOUR SOFTENER
KEEP THE SOFTENER FROM FREEZING FIG. 11 DRAIN WATER FROM THE
If the softener is installed where it could freeze (summer cabin, lake home, etc. ), you must drain all water from it to stop possible freeze damage. Close the shut off valve on the house main water
pipe, near the water meter or pressure tank. Close the inlet and outlet valve in a 3 valve bypass system, and open the bypass valve. If you want water in the house pipes again, reopen the shut off valve on the main water pipe. SLOWLY and CAREFULLY tip it over until the rim rests on the wood block with the inlet and outlet over the drain. Do not allow the softener's weight to rest on the inlet and outlet fittings or they will break. Carefully remove the large holding clips at the
softener inlet and outlet (see Key No. Remove the brinewell cover and disconnect the
CARE OF YOUR SOFTENER
HELPFUL HINTS CHECKLIST . . . TO HELP YOU SAVE MONEY
If your water softener fails to work, make the following easy checks. Often, you will find what's wrong yourself and you won't have to call and wait for service. [. . . ] WATER FLOW THROUGH THE SOFTENER VALVE
BRINING AND BRINE RINSE CYCLES
bypass hard water to valve outlet venturi drain nozzle brine from salt storage tank from Valve Inlet (hard water)
After fill, timer/switch action allows the motor to turn the rotor and disc into BRINING position. Suction, created by the nozzle and venturi, draws brine from the salt storage tank and injects it into the resin bed via the bottom distributor. When the brine valve closes to end brine draw, water flow continues in the same directions to slowly RINSE brine from the resin bed and to the drain.
bypass hard water to valve outlet flow plug
Timer/switch action again allows the motor to turn the rotor & disc to place the valve in BACKWASH, stopping water flow to the nozzle. Water is routed down and out the bottom distributor, up through the bed, and out the top distributor to the drain. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE BOSCH SMI 63M52EU/81
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual BOSCH SMI 63M52EU/81 will begin.