User manual BOSCH SMI 63M56EU/80 SUPPLEMENT

[. . . ] SAVE THIS MANUAL Use the plastic bag and tie provided, to hang manuals nearby the softener for future reference. · Warranty · Installation · Start Up / Setting Timer · How It Works · Care Of · Specifications · Repair Parts Systems Tested and Certified by NSF International against NSF/ANSI Standard 44 for softener performance. Sears, Roebuck and Co. , 3333 Beverly Road, Hoffman Estates, IL 60179 USA PRINTED IN U. S. A. www. KenmoreWater. com Part No. D 10/18/06) WARRANTY ON WATER SOFTENER ONE YEAR LIMITED WARRANTY ON WATER SOFTENER When installed, operated and maintained according to all instructions supplied with the product, if this Kenmore appliance fails due to a defect in material and workmanship within one year from the date of purchase, call 1-800-4-MY-HOME® to arrange for free repair. TEN YEAR LIMITED WARRANTY AGAINST LEAKS When installed, operated and maintained according to all instructions supplied with the product, if the water softener tank or salt storage drum develops a leak within ten years from the date of purchase, call 1-800-4MY-HOME® to arrange for free tank or drum replacement. After the first year you must pay an initial trip charge. [. . . ] You can start a regeneration right away, or you can set the timer to regenerate at the next 2:00 AM (or other preset recharge time). 8 OFF 7 6 5 4 3 2 1 SERV FILL PM RECHARGE WATER FLOW FIG. 31 8 OFF 7 6 5 4 3 2 1 PM RECHARGE TONIGHT WATER FLOW FIG. 32 RECHARGE NOW Press the REGENERATION button and hold until *RECHARGE, Serv and Fill begin to flash in the display. Upon reaching fill, the first cycle of regeneration, the flashing Serv goes off and Fill is on steady. This regeneration will last for about 2 hours. After the 2 hours, you will have soft water again. * NOTE: If the CLEAN feature is set to ON, a cleaning backwash (CLEAN and Bkwsh or Rinse flashes in the display, along with the minutes of the clean cycle remaining) precedes the recharge. Salt Level SALT LEVEL Bars, Salt Level Brinewell Decal 8 7 6 5 4 3 2 1 RECHARGE TONIGHT Press and release (do not hold) the REGENERATION button. RECHARGE TONIGHT flashes in the display, and the softener begins regeneration at the next preset recharge time. Press and release the REGENERATION button once more if you decide to cancel the regeneration, and RECHARGE TONIGHT will not flash in the display. Indicator Light FIG. At level 2, the storage tank is about 1/3 full. This is the lowest you should allow the stored salt level to drop to. When installing this unit in the State of California, this setting MUST be ON. California Efficiency Requirement Your Kenmore Water Softener has a "High Efficiency" feature with an "ON" or "OFF" setting. This softener setting is shipped in the "OFF" position, which utilizes the maximum rated capacity while most often achieving maximum salt efficiencies. When installing this unit in the State of California, you MUST turn this setting to the "ON" position which may initiate more frequent recharges, however it will operate at 4000 grains per pound of salt or higher. Press SELECT again to show the CLEAN display. This feature is beneficial on water supplies containing iron and/or high amounts of sediments (sand, silt, dirt, etc. ). When set to ON, a backwash and fast rinse cycle will occur first, preceeding the normal regeneration sequence (see pages 26 - 28). This provides extra cleaning of the resin bed before it is regenerated with the salt brine. To conserve water, if your water supply does not contain iron or sediments, be sure this feature is set to OFF. Press SELECT again until the CLEAN TIME display shows. Clean feature minutes: If you are using this feature, the length of the extra backwash cycle automatically is set to 7 minutes. [. . . ] The electronic timer again energizes the motor to return the valve to service. As the valve rotates, the position switch lever drops to open the circuit. The valve remains positioned in service until the electronic timer initiates the next regeneration. Soft Water To Valve Outlet Drain Position Switch FIG. Call The Kenmore Water Line 1-800-426-9345 41 Exploded View 4 2 3 Kenmore MODEL Nos. [. . . ]