User manual BOSCH SMI 63M56EU/81 SUPPLEMENT

[. . . ] SAVE THIS MANUAL Use the plastic bag and tie provided, to hang manuals nearby the softener for future reference. · Warranty · Installation · Start Up / Setting Timer · How It Works · Care Of · Specifications · Repair Parts Systems Tested and Certified by NSF International against NSF/ANSI Standard 44 for softener performance. Sears, Roebuck and Co. , 3333 Beverly Road, Hoffman Estates, IL 60179 USA PRINTED IN U. S. A. www. KenmoreWater. com Part No. E 12/8/06) WARRANTY ON WATER SOFTENER ONE YEAR LIMITED WARRANTY ON WATER SOFTENER When installed, operated and maintained according to all instructions supplied with the product, if this Kenmore appliance fails due to a defect in material and workmanship within one year from the date of purchase, call 1-800-4-MY-HOME® to arrange for free repair. THREE YEAR LIMITED WARRANTY ON ELECTRONIC PARTS When installed, operated and maintained according to all instructions supplied with the product, if any of the following electronic parts fail due to a defect in material or workmanship, call 1-800-4-MY-HOME® to arrange for free part replacement: Brine Tank Light, Electronic Board, Sensor Housing, Wiring Harness, Transformer, Micro Switch, Drive Motor, Power Cable. After the first year you must pay an initial trip charge. [. . . ] You can start a regeneration right away, or you can set the timer to regenerate at the next 2:00 AM (or other preset recharge time). SALT SIGNAL LEVEL LEVEL 8 7 6 5 4 3 2 1 PM RECHARGE NOW FIG. 33 SALT SIGNAL LEVEL LEVEL RECHARGE NOW Press the REGENERATION button and hold until *RECHARGE, Serv and Fill begin to flash in the display. Upon reaching fill, the first cycle of regeneration, the flashing Serv goes off and Fill is on steady. This regeneration will last for about 2 hours. After the 2 hours, you will have soft water again. * NOTE: If the CLEAN feature is set to ON, a cleaning backwash (CLEAN and Bkwsh or Rinse flashes in the display, along with the minutes of the clean cycle remaining) precedes the recharge. 8 7 6 5 4 3 2 1 PM RECHARGE TONIGHT FIG. 34 Indicator Light Bars, Salt Level SALT SIGNAL LEVEL LEVEL SALT LEVEL Brinewell RECHARGE TONIGHT Press and release (do not hold) the REGENERATION button. RECHARGE TONIGHT flashes in the display, and the softener begins regeneration at the next preset recharge time. Press and release the REGENERATION button once more if you decide to cancel the regeneration, and RECHARGE TONIGHT will not flash in the display. Decal Salt Level 8 7 6 5 4 3 2 1 FIG. 35 SALT MONITOR SYSTEM The face plate timer has a low salt monitor with an indicator light to remind you to add salt to the storage tank. Lift the salt hole cover and level the salt in the storage tank. (May recharge more often using smaller salt dosage and less water). When installing this unit in the State of California, this setting MUST be ON. California Efficiency Requirement Your Kenmore Water Softener has a "High Efficiency" feature with an "ON" or "OFF" setting. This softener setting is shipped in the "OFF" position, which utilizes the maximum rated capacity while most often achieving maximum salt efficiencies. When installing this unit in the State of California, you MUST turn this setting to the "ON" position which may initiate more frequent recharges, however it will operate at 4000 grains per pound of salt or higher. Press SELECT1 again to show the CLEAN display. This feature is beneficial on water supplies containing iron and/or high amounts of sediments (sand, silt, dirt, etc. ). When set to ON, a backwash and fast rinse cycle will occur first, preceeding the normal regeneration sequence (see pages 26 - 28). This provides extra cleaning of the resin bed before it is regenerated with the salt brine. To conserve water, if your water supply does not contain iron or sediments, be sure this feature is set to OFF. Press SELECT1 again until the CLEAN TIME display shows. [. . . ] Call The Kenmore Water Line 1-800-426-9345 42 Parts List Kenmore MODEL Nos. 1 1 2 3 -- 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Part Number ------7284304 7284231 7284338 7088033 7176292 7141001 7288560 7275907 7284540 7284532 7284639 7252268 7286021 7265025 7219888 7082150 7003847 7100819 7137913 7287140 7284613 0900431 1103200 9003500 7239155 7105047 0502272 7287182 7170270 7077870 7170254 7170296 3442699 7287213 7282603 Part Description Cover Lock (Required for shipping only) Rim Insert (Required for shipping only) Cover (main) Salt Hole Cover (order following decal) Instruction Decal Clamp Retainer (2 required) Clamp Section (2 required) Vapor Barrier Timer Repl. (PWA) Transformer, 24 V - 10 VA Faceplate (order following decal) Faceplate Decal Rim (includes key no. 11 & 12) O-Ring, 11/16" x 1-1/32" Light Asm. [. . . ]