User manual BOSCH TAS 5546GB/05 SHORT INSTRUCTIONS

[. . . ] 20 Adjusting the height of the coffee spouts . 20 Preparing espresso and coffee from freshly ground beans . 21 To prepare two cups at the same time . 22 Making espresso and coffee using ready ground coffee . [. . . ] Alternatively, you can measure the hardness yourself using the enclosed test strip: ^ Dip the strip in your drinking water for approximately a second, then shake off any excess water. The result will be evident after about a minute. If the water is harder than 40 °d / 7. 0 mmol/l, limescale will build up more rapidy than with soft water. Descaling will need to be carried out more regularly than stated to prevent limescale damage to the machine. The machine has four programmable levels: Level (machine) Hardness (local water) °d mmol/l Water through-flow in litres Steam through-flow in minutes approx. 30 min Soft 1 Medium 2 Hard 3 Very hard 4 1 (soft) 1 (soft) 2 (medium) 3 (hard) 4 (very hard) 0-3 4-7 7 - 14 0 - 0. 6 0. 7 - 1. 3 1. 3 - 2. 5 14 - 21 2. 5 - 3. 8 above 21 above 3. 8 43 Settings: Customising your machine To set the correct water hardness level, ^ touch the sensor beside "Settings". Settings ß Total no. of coffees ß System lock ß Water hardness ^ Touch the sensor beside "Water hardness". ^ Touch the upper or middle sensor on the right until the correct water hardness is visible on the left of the display. ^ Touch the sensor beside the correct water hardness. A tick will appear beside the water hardness which is currently set. ^ Touch the sensor beside "ok" to save the setting. Selecting or altering a user profile To cater for different tastes and preferences, you can enter up to 10 individual user profiles and also allocate different settings for amount of coffee, temperature, pre-brewing and portion size to them later (see "Setting the portion sizes"). ^ Then touch the sensor beside "ok". 46 Settings: Customising your machine Display You can adjust both the contrast and the brightness of the display: ^ Touch the sensor beside "Settings". Settings ß Water hardness ß User profile ß Display ^ Touch the sensor beside "Display". ^ Touch the sensor beside Contrast or Brightness and set the level with the middle sensor on th right or left of the display. ^ Touch the sensor beside "ok" to save the setting. Buzzer tones You can choose for an audible tone to sound each time a sensor is touched. ^ Touch the sensor beside "Settings". Settings ß User profile ß Display ß Buzzer tones ^ Touch the sensor beside "Buzzer tones". You can now choose whether you want an audible tone to sound each time a sensor is touched (touch the sensor beside "On") or not (touch the sensor besde "Off"). If you select "On", you can then set the volume. The higher the number, the louder the audible tone. 47 Settings: Customising your machine Plate warmer You can connect a Miele EGW 4000-14 or EGW 4000-29 plate warmer to the coffee machine using a special connection cable available as an optional accessory from your Miele Dealer or the Miele Spare Parts Department. Once the plate warmer is connected, you will need to "install" the plate warmer in the "Settings" menu. ^ Touch the sensor beside "Settings". Settings ß Display ß Buzzer tones ß Plate warmer ^ Touch the sensor beside "Plate warmer". There are three options: Automatic The plate warmer will switch on and off together with the coffee machine. The plate warmer must be switched on with the On/Off control. [. . . ] For extra safety it is advisable to install a residual current device (RCD), with a trip current of 30 mA (in accordance with DIN VDE 0664, VDE 0100, Section 739). If the socket is not accessible after installation (depending on country) an additional means of disconnection must be provided for all poles. WARNING: THIS APPLIANCE MUST BE EARTHED 80 Electrical connection U. K. , ZA, IRL Non-rewireable plugs BS 1363 The fuse cover must be refitted when changing the fuse, and if the fuse cover is lost, the plug must not be used until a suitable replacement is obtained. The colour of the correct replacement cover is that of the coloured insert in the base of the plug, or the colour that is embossed in words on the base of the plug (as applicable to the design of plug fitted). [. . . ]