User manual BOSCH TDS1135GB

[. . . ] Solving Minor Problems Yourself Problem Possible Causes Temperature control (H) set to minimum Iron does not work or is not heating up Connection problems The automatic shut-off system has been activated (*) There is no water in the tank The temperature control (H) is set too low, the pump does not work because the temperature limiter is working You have pressed the shot of steam button (E) repeatedly without waiting for 5 seconds between each press The temperature regulator (H) has been set to "calc`n clean" position while the iron is still hot. Temperature regulator (H) very low Solution Turn the temperature control to a higher position Check that the plug is inserted into the mains socket correctly Move the iron gently from side to side to re-start Fill the water tank Set the temperature control within the steam " "area, between"··" and "max" Wait 5 seconds between each press of the jet of steam button Change the temperature regulator setting. Iron is not steaming Water is dripping from the holes in the soleplate Water comes out together with steam Steam regulator (A) set too high in conjunction with a low temperature. There is no water in Iron emits noise the tank, the pump is operating dry Temperature too high Garments tend to stick During first use: Certain components on the appliance have been lightly greased at the factory and may produce a little smoke when initially heated. Auto-shut off has been activated. Turn the temperature control to a higher position and wait until the lamp (A) goes out. [. . . ] It may smoke and smell ­ this is normal and will cease after a short while. When using the steam function for the first time, do so away from the garment, as there could still be some dirt in the steam dispenser. If necessary, carefully clean the soleplate down with a dry, folded cloth Cleaning and Maintenance Attention !For general cleaning, follow the information below: Problem Dirty/lightly marked iron body or soleplate Mark develops on soleplate during use Heavily stained soleplate Solution Clean the body of iron or soleplate with a damp cloth then dry it. Set the iron to its maximum temperature setting. Rub the iron a few times over with a dry cotton cloth folded several times. While the iron is cold, iron a linen cloth soaked in white vinegar. Then dampen a cloth with water and wipe the soleplate clean and dry thoroughly. DO NOT de-scale or clean the water tank with cleaning products or solvents, (unless recommended by Bosch) as these could cause the iron to drip when using the steam function. DO NOT use sharp objects or abrasive products to clean the soleplate or any other part of the appliance. To keep the soleplate in good condition, do not allow it to come into contact with metal objects. Using Your Iron 3. Setting the temperature The temperature control (H) adjusts the temperature of the soleplate (I). M. The green pilot lamp (L) on the handle will stay lit while the pump button (G) is pressed. If you press it when the water tank is empty, you will hear a distinctive sound of the pump operating dry. Note:Atatemperaturesettingof"·", thesoleplateisnothotenough to produce steam so the steam regulator should be set to the "­" position to avoid water dripping from the soleplate (I). to n 1. Check the temperature instructions shown on the care label of the garment you are ironing and set the temperature control (H) to the corresponding position by lining it up with the pointer (F) on the iron: Fabric Synthetics Silk - Wool Cotton - Linen Temperature Setting · ·· ··· calc'n clean Silk-Wo o lC Sy nth min ic B. Spray button Sy nth min et et s C. Ironing with shot of steam This can be used to remove stubborn wrinkles or to press in a sharp crease or pleat. It cannot be used on a synthetic setting for delicate items. 1. Setthetemperaturecontrol(H)tothe"···"or"max"position. Set the steam regulator (A) to the «+» position. Press the shot of steam (E) button on the handle repeatedly at intervals of 5 seconds. 2. If you are unsure what type of material the garment is made from, start ironing on the lowest temperature setting and increase accordingly. If the garment is made from mixed fabrics, set the temperature for the most delicate material. D. [. . . ] You may hear a clicking sound when this system is in operation. 8. Spray This can be used to remove stubborn wrinkles. 1. Do not use the spray function with silk as staining may occur. Make sure that there is water in the tank (J). [. . . ]