User manual BOSE 4.2 DIRECT REFLECTING

[. . . ] They may cause a fire or chemical burn if mishandled. Do not recharge, disassemble, heat above 100ºC (212ºF), or incinerate. Replace only with batteries of the correct type and model number. Please dispose of used batteries properly, following any local regulations. [. . . ] Plug one end of the Bose® link cable into the Bose link OUT connector on your LIFESTYLE® system control console. Control console (main room) Antenna cable Antenna (bare wire) Because the antenna radiates at 90 degrees to the antenna (bare wire), mount the antenna vertically as close as possible to the center of the house. Do not bundle the antenna together with other cables and do not place it close to large metallic objects or surfaces. 2. Connect the other end of the Bose link cable to your expansion product. Your expansion product might be a speaker system or an AL8 Homewide Wireless Audio Link if you are making a wireless connection. Refer to the owner's guide that came with your expansion product for more information on making this connection. 2 English TAB 2 TAB 3 TAB 4 TAB 5 TAB 6 TAB 7 TAB 8 EXPANDING YOUR LIFESTYLE® SYSTEM Getting the remote ready 1. Make sure your 4. 2 DIRECT REFLECTING remote and expansion product are set to the same room code. The remote you received is set to room code B. If the expansion product is also set to room B, you do not need to do anything. To change the remote control room code, see "Changing the room code" on page 8. To change the room code in the expansion product, see the owner's guide that came with it. Make sure the house code in the 4. 2 DIRECT REFLECTING remote is the same as in your LIFESTYLE® V25/V35 home entertainment system. Returns to last TV channel or radio station preset. 7 Numeric keypad Selects a CD track, DVD chapter, radio station preset, or TV channel that corresponds to the numbers pressed. Enters a dash or dot as necessary for a digital TV channel number. Confirms channel selection on certain TVs. Note: If these controls do not seem to work with your TV, you may need to plug an IR emitter cable into the IR connector on the rear panel of the control console. See the address list included with your LIFESTYLE® system for contact information. Although the LIFESTYLE® system control console emits IR signals into the room where it is located, an IR emitter can better direct those signals to the TV. 7 TAB 8 TAB 7 TAB 6 TAB 5 TAB 4 TAB 3 TAB 2 English USING MULTI-ROOM AUDIO Room and house codes Room and house codes are the settings that allow you to operate your main room system from another room in your home that has a Bose® link-enabled expansion system. Each 4. 2 DIRECT REFLECTING remote and your main room system must have identical house codes. Also, each expansion system and the 4. 2 DIRECT REFLECTING remote used with it must have identical room codes. Locate the room code switches (6-9). Changing the room code Your 4. 2 DIRECT REFLECTING remote is set at the factory for room code B. If room code B is already used by another Bose link product in your home, you need to change both the 4. 2 DIRECT REFLECTING and expansion system to another room code. To change the room code in your 4. 2 DIRECT REFLECTING remote: 1. Press and slide the battery cover off the back of the remote. 8 English TAB 2 TAB 3 TAB 4 TAB 5 TAB 6 TAB 7 TAB 8 USING MULTI-ROOM AUDIO 3. Select a room code from the following table. Room Code B C D E F G H I J K L M N O 6 7 8 9 4. [. . . ] Using a fine-point pen or other small tool, set switches 1-4 to the corresponding up and down positions shown for that house code. Slide the battery cover back into place until it snaps closed. Go to the main room and press the Setup button on the control console. Return to the expansion room and press the Stop button ( ) on the 4. 2 DIRECT REFLECTING remote. [. . . ]