User manual BOSS BV-14.1FLIP

[. . . ] Refer any repairs to a qualified service technician. · Do not attempt to repair a damaged, broken or faulty power cord. [. . . ] Use only a power source with 12 Volts DC (negative ground). Before final installation, temporarily connect the wiring according to the diagram near the end of this manual, check it to ensure that it has been connected properly, and test the unit to make sure it is working correctly. After the monitor is installed, do not arbitrarily pull it down or strike it. This may loosen the mounting screws and cause it to fall down. Operating precautions Turn the unit off when it is not in use. Avoid dropping any metal objects or inflammable items into the monitor ventilation slots. Do not place objects on or suspend objects from the power cord, as this may damage the cord. BV14. 1FLIP User's Manual User's Manual - page 3 Features Your new video monitor features the following: · TFT Active Matrix LCD display · Wireless infrared audio transmitter and headphones · Overhead console mounting bracket · On-screen menu system · Audio/video input controls What is included? When first unpacking your new flipdown monitor, please check first that the package contains all of the items below. If something is missing, contact the store where you purchased the player. · LCD monitor housing · Wireless headphones · Wireless remote control with batteries · RCA-RCA video cable · Built-in dome lights · Wireless remote control · Video/power interface cable with inline fuse · Metal mounting plate · (10) M4x6mm sheet metal screws (for attaching mounting plate to ceiling) · (10) M4x10mm machine screws (for attaching monitor to mounting plate) BV14. 1FLIP User's Manual - page 4 Monitor Controls and Features 5 1 2 3 4 6 7 8 9 V1 V2 1 DOME LIGHT ON/OFF MODE This switch is used to determine if the lights go on/off automatically with the opening of a car door. 6 MENU/SELECT This button enables the on-screen display menu system. Once enabled, this button is used as a SELECT button. 2 POWER ON/OFF 3 VIDEO SOURCE #1 SELECTOR 4 VIDEO SOURCE #2 SELECTOR 5 MONITOR RELEASE BUTTON 7 INCREASE/DECREASE BUTTONS 8 or increase the value of the parameter currently selected in the menu system. These buttons are used to decrease 9 MANUAL DOME LIGHT ON/OFF This button turns the monitor system on and off. BV14. 1FLIP User's Manual - page 5 Remote Control 1 POWER Press to turn unit ON or OFF. 1 POWER MUTE UP 7 2 UP/DOWN BUTTONS These buttons are used to increase or decrease parameters in the onscreen display menu system. 2 3 V1/V2 MENU 8 3 VIDEO SELECT Use this button to switch between A/V Source 1 and A/V Source 2. DOWN 4 MODE CHANNEL SCAN VOLUME 8 MENU/SELECT This button enables the on-screen display menu system. Once enabled, this button is used as a SELECT button. 9 5 6 NOTE: These buttons have no function on this monitor. 4 CHANNEL UP/DOWN 5 MODE 6 SCAN 7 MUTE 9 VOLUME This button has no function on this monitor. BV14. 1FLIP User's Manual- page 6 System wiring On a towel or soft cloth, gently place the monitor assembly "face down" on a stable worksurface. Using the wires provided, complete the audio, video and power connections in your vehicle as shown in the diagram below. BLUE GREEN PURPLE YELLOW WHITE VIDEO OUTPUT L AUDIO OUTPUTS R VIDEO SOURCE 1 (DVD player, video game, etc. ) RED RED WHITE RED YELLOW WHITE VIDEO OUTPUT L AUDIO OUTPUTS R VIDEO SOURCE 2 (DVD player, video game, etc. ) RED RED POWER BLACK FUSE to +12 VDC Battery to Chassis Ground RED to +12 VDC Battery DOME LIGHTS BLACK YELLOW GREEN to Chassis Ground Car dome lamp (+) Car dome lamp (-) BV14. 1FLIP User's Manual User's Manual - page 7 Monitor installation CAUTION: Make sure the screws are NOT long enough to go through the roof! If you have any doubts about this type of installation, please consult your local mobile electronics retailer. Making holes in the roof of your vehicle will cause damage which is expensive to repair. notch toward the front Using the TEN black selftapping screws provided, attach the monitor mounting plate by screwing through the headliner and into the existing roof supports or the wood bracket you made (see TIP below). USE HIGHLIGHTED HOLE LOCATIONS ONLY!! Install the monitor onto the mounting plate, using the eight screws provided. INSTALLATION TIP Make a MOUNTING BRACKET out of wood. This bracket mounts under the headliner, and provides a mounting surface to which the housing of the flip-down monitor can be attached. BV14. 1FLIP User's Manual - page 8 Releasing and lowering the monitor To lower the monitor, press the Monitor Release button and pull the monitor down. [. . . ] To replace the batteries, remove the battery cover by placing your finger in the depression on the housing and firmly pulling the cover off. Insert the two batteries, carefully noting the polarity (it is marked inside the battery cavity). [. . . ]