User manual BOSS BV-15FLIP

[. . . ] Refer any repairs to a qualified service technician. · Do not attempt to repair a damaged, broken or faulty power cord. · To avoid risk of electronic shock or damage to the monitor, do not permit any of this equipment to become damp or wet from water or drinks. [. . . ] · LCD monitor housing · Wireless remote control with battery · RCA-RCA video cable · Video/power interface cable with inline fuse · Metal mounting plate · (4) Silver sheet metal screws (for attaching mounting plate to ceiling) · Overhead console mounting bracket · On-screen menu system · Audio/video input controls · Built-in dome lights · Wireless remote control · (6) Black machine screws (for attaching monitor to mounting plate) BV15FLIP User's Manual - page 4 Monitor Controls and Features MENU POWER 1 2 3 4 5 1 INFRARED REMOTE SENSOR 2 UP/DOWN BUTTONS These buttons are used to decrease or increase the value of the parameter currently selected in the menu system. 3 MENU/SELECT This button enables the on-screen display menu system. Once enabled, this button is used as a SELECT button. 4 POWER ON/OFF 5 POWER LED BV15FLIP User's Manual - page 5 Remote Control 1 POWER Press to turn unit ON or OFF. 2 UP/DOWN BUTTONS These buttons are used to increase or decrease parameters in the onscreen display menu system. 1 2 3 MENU/SELECT This button enables the on-screen display menu system. Once enabled, this button is used as a SELECT button. 3 4 VIDEO SELECT Use this button to switch between A/V Source 1 and A/V Source 2. 4 5 4 MUTE Press this button to turn off the audio part of the program you are watching. Press again to turn it back on. Replacing the battery in the remote control The remote battery is held in a small "drawer" on one edge of the remote. To open this drawer, press and hold the small button on the edge of this drawer (as shown below) and slide the drawer out. Battery Insert a new battery and push the drawer back fully into the remote. Release button BV15FLIP User's Manual- page 6 System wiring Using the wires provided, complete the audio, video and power connections in your vehicle as shown in the diagram below. WHITE VIDEO SOURCE (DVD player, video game, etc. ) L AUDIO OUTPUTS R RED YELLOW VIDEO OUTPUT RED POWER BLACK FUSE 12V Battery to Chassis Ground RED for DOME LIGHTS WHITE BLACK to +12 VDC (constant) to +12 VDC (dome light trigger) to Chassis Ground BV15FLIP User's Manual - page 7 Monitor installation CAUTION: Make sure the screws are NOT long enough to go through the roof! If you have any doubts about this type of installation, please consult your local mobile electronics retailer. Making holes in the roof of your vehicle will cause damage which is expensive to repair. NOTE BRACKET ORIENTATION (notches to front and back) Attach the monitor mounting plate by screwing through the headliner and into the existing roof supports or the wood bracket you made (see TIP below). Before screwing monitor to bracket, remove paper from self-adhesive pads to provide stability during installation. Align monitor base on the six screwposts on the mounting plate, and use the six machine screws provided to attach the monitor to the plate. INSTALLATION TIP Make a MOUNTING BRACKET out of wood. This bracket mounts under the headliner, and provides a mounting surface to which the housing of the flip-down monitor can be attached. BV15FLIP User's Manual - page 8 Releasing and lowering the monitor To lower the monitor, press the Monitor Release button and pull the monitor down. To lower the monitor further, continue pulling down and the internal mechanism will permit further movement and will hold the monitor in the position in which you leave it. PUSH the monitor release button Pull the monitor screen down to the desired angle To avoid accidental damage, we suggest you always close the monitor assembly when it is not in use. Test that it is secured by gently pulling down on monitor frame. BV15FLIP User's Manual - page 9 Powering up the monitor To turn the monitor on, press the POWER button on the monitor or the remote control. To adjust the monitor image, press MENU to access the On-Screen Display system. See the next page for details on all the functions available for adjustment. Turning on the dome lights This monitor features a two-position switch for controlling the built-in dome lights. The center position of the switch (marked with a "0") turns the lights off. The position marked "I" will permit the dome lights to come on whenever the vehicle's built in dome lights are on. The "II" position turns the lights on until you move the switch to a different position. Three position dome light switch BV15FLIP User's Manual - page 10 On-screen menu system This monitor incorporates an on-screen menu display systems which permits you to setup the monitor for a wide variety of installations and applications. Enter the menu system by pressing the MENU button on the front of the monitor or the remote control. [. . . ] Use the < and > buttons to step through the following languages: English (the default language), German, French, Italian, Spanish, Chinese Traditional, Chinese Simple, and Japanese. OSD H Position and OSD V Position settings permit adjustment of the horizontal and vertical position of the On-Screen Display. Use the < and > buttons to make these adjustments. [. . . ]