User manual BOSS BV-17FLIP

[. . . ] · If there is smoke or any peculiar odor present during use, or if there is damage to any of the component enclosures, immediately unplug the power cord and send the monitor to your local dealer or service center as soon as possible . Safety precautions · Do not operate this equipment while driving ­ safe driving should always be your highest priority. · This product should not be installed in a location which allows the monitor screen to be visible to the driver of the vehicle. In some states and countries, the viewing of images on a screeen inside a vehicle is illegal, even by people other than the driver. Be sure that the installation and operation of this system is in compliance with local rules and regulations. SHOCK HAZARD! [. . . ] Before final installation, temporarily connect the wiring according to the diagram near the end of this manual, check it to ensure that it has been connected properly, and test the unit to make sure it is working correctly. After the monitor is installed, do not arbitrarily pull it down or strike it. This may loosen the mounting screws and cause it to fall down. Operating precautions Turn the unit off when it is not in use. Avoid dropping any metal objects or inflammable items into the monitor ventilation slots. Do not place objects on or suspend objects from the power cord, as this may damage the cord. BV15FLIP User's Manual - page 3 Features Your new video monitor features the following: · TFT Active Matrix LCD display · Built-in infrared audio transmitter (for use with model HP-10 headphones, sold separately) What is included? When first unpacking your new flipdown monitor, please check first that the package contains all of the items below. If something is missing, contact the store where you purchased the player. · LCD monitor housing · Wireless remote control with battery · RCA-RCA video cable · Video/power interface cable with inline fuse · Metal mounting plate · (4) Silver sheet metal screws (for attaching mounting plate to ceiling) · Overhead console mounting bracket · On-screen menu system · Audio/video input controls · Built-in dome lights · Wireless remote control · (6) Black machine screws (for attaching monitor to mounting plate) BV15FLIP User's Manual - page 4 Monitor Controls and Features MENU POWER 1 2 3 4 5 1 INFRARED REMOTE SENSOR 2 UP/DOWN BUTTONS These buttons are used to decrease or increase the value of the parameter currently selected in the menu system. 3 MENU/SELECT This button enables the on-screen display menu system. Once enabled, this button is used as a SELECT button. 4 POWER ON/OFF 5 POWER LED BV15FLIP User's Manual - page 5 Remote Control 1 POWER Press to turn unit ON or OFF. 2 UP/DOWN BUTTONS These buttons are used to increase or decrease parameters in the onscreen display menu system. 1 2 3 MENU/SELECT This button enables the on-screen display menu system. Once enabled, this button is used as a SELECT button. 3 4 VIDEO SELECT Use this button to switch between A/V Source 1 and A/V Source 2. 4 5 4 MUTE Press this button to turn off the audio part of the program you are watching. Press again to turn it back on. Replacing the battery in the remote control The remote battery is held in a small "drawer" on one edge of the remote. To open this drawer, press and hold the small button on the edge of this drawer (as shown below) and slide the drawer out. Battery Insert a new battery and push the drawer back fully into the remote. Release button BV15FLIP User's Manual- page 6 System wiring Using the wires provided, complete the audio, video and power connections in your vehicle as shown in the diagram below. WHITE VIDEO SOURCE (DVD player, video game, etc. ) L AUDIO OUTPUTS R RED YELLOW VIDEO OUTPUT RED POWER BLACK FUSE 12V Battery to Chassis Ground RED for DOME LIGHTS WHITE BLACK to +12 VDC (constant) to +12 VDC (dome light trigger) to Chassis Ground BV15FLIP User's Manual - page 7 Monitor installation CAUTION: Make sure the screws are NOT long enough to go through the roof! If you have any doubts about this type of installation, please consult your local mobile electronics retailer. Auto Phase adjusts the ADC sampling clock phase, relative to the source video H-sync signal. This has the effect of minimizing video distortion and jitter. Auto Clock adjusts the number of pixels from the source video. The number of horizontal pixels displayed is matched to the number of horizontal source pixels. This minimizing vertical bars, stripes or similar artifacts on the display background. Auto Color adjusts and balances the RGB colors. BV15FLIP User's Manual - page 12 OSD (On screen display) menu In the Language menu, you can select the language you want to use in the On-Screen display system. Use the < and > buttons to step through the following languages: English (the default language), German, French, Italian, Spanish, Chinese Traditional, Chinese Simple, and Japanese. OSD H Position and OSD V Position settings permit adjustment of the horizontal and vertical position of the On-Screen Display. Use the < and > buttons to make these adjustments. OSD Timer settings determine how long the On-Screen Display remains on the screen when not in use. The default setting (YES) turns the OSD image off after 20 seconds. [. . . ] The infrared signal is emitted from the large dark lens on the underside of the monitor base. Best sound will be obtained if you sit directly in front of the monitor within about six feet. If you choose to sit to one side of the monitor, you can expect good reception within 35º to the right or left of the monitor. BV15FLIP User's Manual - page 14 Troubleshooting If you experience operation or performance problems with this product, compare your installation with the electrical wiring diagram on the previous page. If problems persist, read the following troubleshooting tips which may help eliminate the problems. [. . . ]