User manual BOSS BV7.2FLIP

[. . . ] · if there is smoke or any peculiar odor present during useor if there is damage to any of the component enclosures, immediately unplug the power cord and send the monitor to your local dealer or service center as soon as possible . Safety precautions · Do not operate this equipment while driving ­ safe driving should always be your highest priority. · This product should not be installed in a location which allows the monitor screen to be visible to the driver of the vehicle. In some states and countries, the viewing of images on a screeen inside a vehicle is illegal, even by people other than the driver. Be sure that the installation and operation of this system is in compliance with local rules and regulations. [. . . ] Wire this cord to an accessory wire which has +12v power when the ignition is switched on. This will prevent the operaton of the monitor when the engine is running. If you do not know how to install the Safety Cord, please consult with a mobile video installer in your area, and have this work completed properly before operating the video system. SHOCK HAZARD!There are dangerous voltages present within the unit. There are no user-serviceable parts within the unit. BV7. 3FLIP · BV7. 31RF · BV8FL · BV8WFLIP · BV8IRF User's Manual - page 1 Installation precautions Choose a mounting location in your vehicle where the unit will not distract or otherwise interfere with the driver's ability to control the vehicle. Do not install components in areas which are susceptible to rain, moisture, direct sunlight, extreme heat or cold, excessive dust, dirt or humidity. If installation requires drilling holes or other modifications to the vehicle, consult with your nearest dealer or professional car audio installer. Use only the installation parts and hardware provided with the unit to ensure proper installation. Using other parts can cause malfunction and possible damage to your video monitor. Use only a power source with 12 Volts DC (negative ground). Before final installation, temporarily connect the wiring according to the diagram near the end of this manual, check it to ensure that it has been connected properly, and test the unit to make sure it is working correctly. When the power is ON, if an input signal is present, the picture will be displayed on the screen. If no signal is present, the monitor will display the message "NO SIGNAL. " If you know a video input signal is present but the monitor displays "NO SIGNAL, " be sure to try pressing the AV SELECT button to see if your input source is connected to the other AV input. To adjust the monitor image, press MENU to access the various adjustment controls such as BRIGHTNESS and CONTRAST. Use the +/- buttons to adjust each parameter until you are satisfied with the picture quality. Turning on the dome lights This monitor features separate ON/OFF buttons for the right and left dome lights, so that if you need not disturb a sleeping companion if you need overhead illumination. The dome lights turn on when you open a door. To turn on or off the dome lights manually, simply press the round button near the right dome light. To turn the dome lights on or off manually, simply press the round button on the side you wish the light to turn on. BV7. 3FLIP · BV7. 31RF · BV8FL · BV8WFLIP · BV8IRF User's Manual - page 11 Infrared Audio Transmission (BV7. 3IRF and BV8IRF only) The BV7. 3IRF and BV8IRF monitors include a wireless infrared transmitter. The transmitter sends a high-quality stereo signal which can be received by a pair of Boss HP-10 wireless infrared headphones. The infrared signal is emitted from the large dark lens on the front of the monitor console. Best sound will be obtained if you sit directly in front of the monitor within about six feet. [. . . ] Best sound will be obtained if you sit directly in front of the monitor within about six feet. If you choose to sit to one side of the monitor, you can expect good reception within 35º to the right or left of the monitor. 35º 35º Changing the battery in the remote control The remote battery is held in a small "drawer" on one edge of the remote. To open this drawer, press and hold the small button on the edge of this drawer (as shown below) and slide the drawer out. Insert a new battery and push the drawer back fully into the remote. Battery Release button BV7. 3FLIP · BV7. 31RF · BV8FL · BV8WFLIP · BV8IRF User's Manual - page 12 Troubleshooting If you experience operation or performance problems with this product, compare your installation with the electrical wiring diagram on the previous page. [. . . ]