User manual BOSS BVFL10.4-BV10.4IRF-BV7FLIP-BV7IRF

[. . . ] Thank you for making your choice in car video entertainment! 8 9 10 11 12 12 13 14 15 16 System wiring: BV10. 4IRF · BV7IRF Monitor installation Releasing and opening the monitor Powering up the monitor Turning on the dome lights Infrared audio transmission: BV10. 4IRF · BV7IRF On screen menu system Troubleshooting Specifications BVFL10. 4 · BV10. 4IRF · BV7FLIP · BV7IRF User's Manual - Contents BVFL10. 4 · BV10. 4IRF · BV7FLIP · BV7IRF User's Manual General precautions Please read this manual completely and carefully prior to attempting to install your new mobile video equipment. Installed correctly, your equipment will provide you with years of enjoyable and safe usage. Installation of this equipment in any portion of a vehicle which impairs or distracts the driver is improper and dangerous. [. . . ] Use only a power source with 12 Volts DC (negative ground). Before final installation, temporarily connect the wiring according to the diagram near the end of this manual, check it to ensure that it has been connected properly, and test the unit to make sure it is working correctly. After the monitor is installed, do not arbitrarily pull it down or strike it. This may loosen the mounting screws and cause it to fall down. Operating precautions Turn the unit off when it is not in use. Avoid dropping any metal objects or inflammable items into the monitor ventilation slots. Do not place objects on or suspend objects from the power cord, as this may damage the cord. BVFL10. 4 · BV10. 4IRF · BV7FLIP · BV7IRF User's Manual- page 4 Features Your new video monitor features the following: · TFT Active Matrix LCD display · Overhead console mounting bracket · On-screen menu system · Audio/video input controls · Dual built-in dome lights · Wireless remote control What is included? When first unpacking your new flipdown monitor, please check first that the package contains all of the items below. If something is missing, contact the store where you purchased the player. · LCD monitor housing · Wireless remote control with battery · Video/power interface cable with inline fuse · Metal mounting plate BV10. 4IRF and BV7IRF also feature: · Built-in wireless infrared audio transmitter (for use with infrared headphones Model HP-10, sold separately) · Black machine screws (for attaching monitor to mounting plate) BVFL10. 4 · BV10. 4IRF · BV7FLIP · BV7IRF User's Manual - page 5 Monitor Controls and Features DOWN UP MODE POWER 1 2 3 4 5 4 POWER ON/OFF This button turns the monitor system on and off. 1 REMOTE IR SENSOR 2 UP/DOWN BUTTONS These buttons are used to increase or decrease parameters in the onscreen display menu system. 5 POWER LED 3 MODE This button enables the on-screen display menu system. Once enabled, this button is used as an ENTER button. BVFL10. 4 · BV10. 4IRF · BV7FLIP · BV7IRF User's Manual - page 6 Remote Control 1 POWER Press to turn unit ON or OFF. 2 SLEEP This monitor shuts off automatically after a certain period of non-use. Use the time button to change the length of time required before auto shut-off. 1 2 3 POWER SLEEP 3 UP/DOWN BUTTONS These buttons are used to increase or decrease parameters in the onscreen display menu system. 4 5 ­ MODE + AV 4 MODE This button enables the on-screen display menu system. Once enabled, this button is used as an ENTER button. 5 A/V SOURCE SELECTOR Use this button to switch between A/V Source 1 and A/V Source 2. Changing the battery in the remote control The remote battery is held in a small "drawer" on one edge of the remote. To open this drawer, press and hold the small button on the edge of this drawer (as shown below) and slide the drawer out. Insert a new battery and push the drawer back fully into the remote. Battery Release button BVFL10. 4 · BV10. 4IRF · BV7FLIP · BV7IRF User's Manual - page 7 System wiring: BVFL10. 4 and BV7FLIP On a towel or soft cloth, gently place the monitor assembly "face down" on a stable work surface. Using the wires provided, complete the audio, video and power connections in your vehicle as shown in the diagram below. VIDEO SOURCE 1 VIDEO INPUT 1 (YELLOW) BLACK VIDEO INPUT 2 (WHITE) (DVD player, video game, etc. ) VIDEO SOURCE 2 FUSE RED (DVD player, video game, etc. ) 12V Battery BLACK to Chassis Ground RED DOME LIGHTS YELLOW BLACK Constant +12VDC to +12VDC Trigger (for Dome Light) to Chassis Ground BVFL10. 4 · BV10. 4IRF · BV7FLIP · BV7IRF User's Manual - page 8 System wiring: BV10. 4IRF and BV7IRF On a towel or soft cloth, gently place the monitor assembly "face down" on a stable work surface. [. . . ] Enter the menu system by pressing the MODE button on the front of the monitor or the remote control. Pressing the MODE button steps you through the five main screens of the menu system. These are, in order: Color, Picture, OSD (On Screen Display) Menu, Miscellaneous and Exit. [. . . ]