User manual BOSS OUTLAW LAC129D

[. . . ] Bend the backstrap to conform to the mounting case and the dashboard surface to which you plan to secure the backstrap (Figure 2). Slide one of the utility holes on the backstrap onto the support screw and fasten it with the spring washer and nut provided. Using the 5 x 25mm screw and the plain washer, secure the backstrap to the dashboard surface as shown in the diagram. Tighten, secure, and check the overall mounting to be sure it is safe and will not release in an emergency stop or other sudden movement of the vehicle. mounting case support screw head unit Figure 1 Bending the support tabs CD3125R/MP3-3130R User's Manual - page 2 English Español Português Français Deutsch dashboard attachment surface support strap DIN rear mount installation (uses factory radio mounting bracket) 5mm nut spring washer plain washer 5 x 25mm support screw support screw Select a position on the head unit housing where the screw holes of the factory radio bracket align with the threaded screw holes on sides of the head unit (Figure 3). select two mounting hole positions on each side of head unit Figure 2. [. . . ] Do not attempt to disassemble the front panel. Figure 5 Press RELEASE to release the front panel Grasp the right side of the panel and pull to remove it (Figure 6). Figure 6 Grasp the right side of the panel and pull to remove the panel Immediately place the front panel in its protective case for safe and clean storage (Figure 7). Front Panel Figure 7 Place the front panel in its protective case CD3125R/MP3-3130R User's Manual - page 4 English Español Português Français Deutsch Reinserting the front panel Push the front panel into the main body. You should hear a "click. " (Figure 8) NOTE: If the panel fails to lock into position properly, the function of some controls may be impaired, and some segments of the display may not become illuminated. If this occurs, press RELEASE and reinstall the front panel. Removing the head unit Should you need to remove the head unit, first remove and store the front panel as described on the preceding page. After you have removed the front panel, insert your fingers into the groove along the right side or the left side of the frame (not both!) and pull out to remove the bezel (Figure 9). Figure 8 Push panel into main unit until you hear a "click" Figure 9 Pull out to remove bezel Then, insert the levers supplied with the head unit into the grooves on both sides of the unit as shown in the drawing until you feel a "click. " You can now use the levers to pull the unit from the dashboard (Figure 10). Figure 10 Insert levers until "click" occurs, then use levels to pull out head unit. CD3125R/MP3-3130R User's Manual - page 5 English Español Português Français Deutsch General and Tuner Controls 1 23 4 5 10 6 9 8 1 7 General Controls Tu n e r Controls 1 POWER Press any button to turn unit on. Press and hold POWER to turn it off. 3 AS/PS When pressed and held for several seconds, the tuner will search and store the first six strong stations as presets. 2 DISPLAY To set CLOCK, press and hold, then press the TUNE/TRACK button. 5 LOCAL/DISTANT SELECT Press to select between strong (LOC) and weak (DIST) stations. 4 RELEASE Press to release and remove the front panel. 6 MONO/STEREO SELECT Press if reception becomes noisy. Press again for normal stereo reception. 7 STATION PRESETS (1-6) Press any preset to select a station. To store a station in memory, tune to it, and press and hold your choice of preset button for several seconds. 8 STATION SCAN Press this button to make the tuner search the frequency band for stations, playing each for five seconds before moving to next station. 9 TUNE/TRACK BUTTONS Press and release to activate automatic seek function ("AUTO" will appear on display). Press and hold to engage manual tuning mode ("MANUL" will appear on display). 10 BAND Press repeatedly to change between three FM bands/two AM bands. CD3125R/MP3-3130R User's Manual - page 6 English Español Português Français Deutsch Audio Controls 1 2 6 3 5 4 Audio Controls 1 CONTROL KNOB Use this knob to adjust any of the audio control functions you select with the AUDIO button. 5 AUDIO FUNCTION SELECT Press the button repeatedly to access Volume, Bass, Treble, Balance and Fader functions. Then use the ROTARY KNOB to adjust the selected function. 2 EQ (Preset Equalizer Curves) Press repeatedly to cycle through five modes: FLAT, CLASSICAL, POP M, ROCK M or DSP OFF. 6 LOUDNESS Press and hold to increase the level of bass output. 3 MUTE Press to silence the receiver. Press again to return to normal operation. 4 SUBWOOFER/SOURCE SELECT Press and hold to engage subwoofer output ("SUBWOOFER" will appear in display). Press repeatedly to choose desired audio source (Radio, CD or AUX IN). Auxiliary input feature This CD Receiver features an Auxiliary Input jack on the back side of the unit. The unit searches for files whose names have the same characters inputted by the user. The unit displays these sorted files and directories. This system uses the buttons according to the chart below. The selected file can be played by pushing the BAND/LOUD button. Front panel control Band/Loud Preset 1 Preset 2 Preset 3 Preset 4 Preset 5 Preset 6 Source I<< >>I Audio DISP Audio Up/Down Key assignment Enter A, B, C, 1 D, E, F, 2 G, H, I, 3 J, K, L, 4 M, N, O, 5/10 TRK DOWN P, Q, R, 6/10 TRK UP S, T, U, 7 V, W, X, 8 Y, Z, SPACE, 9 CHAR. SELECT (A-Z, 0-9) NOTE: When in Normal Play mode and when in Searching File or Directory Mode, preset buttons 5 and 6 are assigned as 10 TRACK. CHARACTER CHARACTER SHIFT SELECT RIGHT + (A-Z, 0-9) CHARACTER SELECT (A-Z, 0-9) ­ 5/10 6/10 TRACK DOWN TRACK UP CD3125R/MP3-3130R User's Manual - page 10 English Español Português Français Deutsch 1 2 3 4 OUTLAW LAC129D Remote Control 1 POWER Use to turn CD Receiver ON or OFF. 2 AUDIO Press the button repeatedly to access Volume, Bass, Treble, Balance and Fader functions. Then use the I<< and >>I buttons to adjust the selected function. 13 12 11 10 5 6 3 VOLUME Use to increase or decrease volume level. 4 SOURCE Press to choose desired audio source (Radio, CD or AUX IN). 7 5 DISPLAY Use the I<< and >>I buttons to set the clock. 6 AS/PS Use to automatically scan and place six strong stations into memory. 7 PRESETS 1-6 Use to select preset radio stations. 8 REPEAT Press and release to continuously repeat same track. Press again to cancel the repeat function. 9 8 and ) 13 TUNE/SEEK ( 9 CD SCAN Press to audition each track on the current disc. Press again to play the current track. 10 SHUFFLE Press to play ALL tracks on the CD in random order. In Radio Mode, press and release to activate automatic seek function ("AUTO" will appear on display). Press and hold to engage manual tuning mode ("MANUL" will appear on display). In CD Mode, press and release to advance to the next track or to return to the beginning of the current track (track number will be displayed). [. . . ] There is a disc already in the CD player. Excess atmospheric humidity or condensation is present. Head unit is installed at an angle of greater than 30º from horizontal. The built-in microprocessor is not operating properly due to noise. [. . . ]