Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual BOWENS ESPRIT II 250. We hope that this BOWENS ESPRIT II 250 user guide will be useful to you.
Lastmanuals help download the user guide BOWENS ESPRIT II 250.
Detailed instructions for use are in the User's Guide.
[. . . ] Do not restrict slots in case when in use. Care must be exercised when handling equipment that has been in use. The reflector and front end of the unit can become Very Hot. Due to the high voltage/high energy used in the Esprit 250, servicing must be carried out by a qualified, authorised Service Centre.
2.
iii.
iv. [. . . ] The Esprit has a built in photocell enabling the unit to be triggered by the flash from any other flash unit or a small camera mounted flash gun. The photocell is mounted behind the red transparent cover on the top of the Esprit. Sync Socket: The standard quarter inch jack type socket on the rear panel of the unit (Fig. 1. 1) may be used for direct connection to a camera set to `x' synchronisation. Two Esprit 250 flash units may be connected together using a `y' connector. An Infra Red Receiver or Omnicell may also be plugged into this socket. Modelling Lamp Control With the modelling lamp control switch (Fig. 1. 5) in the central position the modelling light is OFF. With the switch set to `Intermittent' the modelling light will go out when the unit is flashed and come back on when the unit comes to ready. This enables the photographer to see from the camera position that all Esprit units in use have fired. With the switch set to `Continuous' the modelling light remains on all the time. The modelling light may be varied in ratio with the flash power output by aligning the indicator line on the modelling output control knob (Fig. 2. 6) with that of the flash control (Fig. 2. 2).
10.
-4-
Bowens Esprit 250 Operating Instructions.
11.
Fuse (Fig. 1. 3) The modelling and flash circuitry is protected by a single 5 amp (F) 20mm fuse mounted on the rear panel. Never replace the fuse with one of a different rating. As the fuse may blow when the modelling lamp fails always check the fuse when replacing bulb. A spare fuse is supplied in the fuse holder. Always switch OFF the Esprit 250 before changing the bulb or fuse. Fitting / Removing A Reflector A range of reflectors is available for the Esprit 250. To fit, slide the neck of the reflector over the front of the unit. Align the three pegs on the reflector with the three slots in the retaining ring. [. . . ] Plug in the sync cord and connect to camera shutter at `x' synchronisation. Alternatively, plug in Infra Red Receiver or Omnicell. Switch ON and select modelling lamp ON or OFF and flash power required. When the unit is ready
14.
-5-
Bowens Esprit 250 Operating Instructions.
to fire the green LED (Fig. 2. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE BOWENS ESPRIT II 250
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual BOWENS ESPRIT II 250 will begin.
