User manual BRANDT A100U1

[. . . ] dishwasher OPERATING INSTRUCTIONS Contents Page 1 - Description of your dishwasher . . 4-5 2 - What to do before using the machine for the first time . . 6-9 Step 1: Adjusting the water softener ­ Measuring the water hardness 6 Mechanical adjustment . . 6 Filling the regenerating salt reservoir . [. . . ] Turn the programmes knob to the desired programme Check that the power cable is plugged into the socket and that the water tap is open. Place glasses, cups and bowls facing downwards. Soak Normal 65°C Eco 55°C Bio 50°C Starting the washing programme Select the programme you desire and press the "Start" button. The programme will start and the "Washing" illuminate. light Depending on the model: when loading large plates into the lower basket, you may have to adjust the height of the upper basket. This can be done even when the basket is full. Adjusting to the HIGH POSITION: Gently lift the basket until you hear the first "Click" on both sides. Adjusting to the LOW POSITION: Lift the basket at the back on both sides ("Click") and then gently lower it. Check that the slides are both at the same height and that the basket is level. Programme end The "Stop" light flashes 15 minutes before the end of the programme. When the programme is finished, the "Stop" light is permanently lit. Rest the programmes knob to position "Stop" to switch off the power to your machine 13 12 The washing programmes Type of items: Mixed -Porcelain, pans, cutlery, glasses, etc. This very short cycle Quantity, type, enables you to rinse amount of food through your items while residue. waiting to wash them until the following day or even the day after. Running a programme and options Mixed Normal amount of dried-on and adhering residue: everyday items Resistant A large amount of dried-on and adhering residue, baked-on stains, grease, residue from frying, cooked cheese, sauce, etc. Delicate A normal amount of slightly sticky residue: everyday items. Cancelling a programme Hold down the "Start Cancel" button for two seconds. The programme will stop and the "Stop" light will light up. Important: Do not forget to lock the waste filter by turning it a quarter turn. 16 17 Protecting the environment Recycling the packaging Warning: Keep all the packaging materials out of children's reach (e. g. plastic bags, polystyrene, etc. ): these can be dangerous for children: risk of suffocation). Recovering and reprocessing packaging material saves on material and reduces the amount of waste. Take your packaging to the nearest recycling centre. Contact your town's local authorities for details of its location. Troubleshooting, what to do? If you are in any doubt about the operation of your machine, before calling a qualified engineer, check the following points (depending on the symptoms noticed). When first using the machine Small door leak Possible causes What to do Recycling your old dishwasher If you wish to dispose of your old dishwasher, make it completely unusable. Break the door lock so that it cannot close (children can become locked in when playing inside the machine ­ risk of suffocation). Remove the electrical plug and cut off the power cable. Take your unusable machine to the nearest recycling centre. Contact your town's local authorities for details of its location. - The machine is wobbly, - Adjust the adjustable not level feet - The door is not correct- - Adjust the rear feet ly centred on the tub - The seal's lip has been - Take off the door seal flattened during storage. - Check that the seal is present and re-tighten the nut - Close the water tap and call an engineer. [. . . ] - Internal fault in the machine - No power supply to the - Check the socket and the fuse socket - Check that the tap is - The tap is closed open - The water supply hose - Check that hose run is kinked - Cancel by pressing - Programme selection "Start" for 3 seconds error and programme and reprogramme blocked - "Start" button held down - Press "Start" only briefly to start the programme too long (> 2 seconds) - Safety system (anti-leak) - Call an engineer. - Remove the protective - Protective cover on the sink's U bend not removed cover - Drainage hose kinked - Check the hose runs correctly behind the machine - Drain filter totally - Remove the filters and blocked clean them and the drain hole - Start a soak programme. If the fault persists, call - Pump blocked. an engineer. Poor washing results Traces of food, deposits, "grains of sand" in the glasses. The machine will not start The machine does not drain. Greasy marks. 20 21 Troubleshooting, what to do? Poor washing results White marks (Identify the nature of the marks) Possible causes - Chalky film (can be removed with vinegar). [. . . ]