User manual BRAVILOR BONAMAT B20HW

[. . . ] D AB C E S T U V W X Y Z AA AB L C G H T (E) (W) E B S F (E) T K S F E B N M P G H K (W) D A R Q (E) M (W) P N L AC AD D A R Q (E) (W) QR G H I J K L M N O F P C Bravilor Bonamat Operating instructions Round­filter coffee brewer with hot water tap GB B5HW, B10HW, B20HW 700. 403. 293F/05­2002 Bravilor Bonamat 05­2002 Bravilor Bonamat Pascalstraat 20 1704 RD Heerhugowaard The Netherlands GB All rights reserved. No part of this document may be copied and/or published by means of printing, photocopying, microfilming or by any other means whatsoever without the prior written consent of the manufacturer. This applies equally to the included drawings and/or diagrams. The information contained in this document is based on general data concerning the construction, materials characteristics and working methods known to us at the time of publication and therefore we reserve the right to make changes without notice. [. . . ] ­ When the symbol appears in the menu, the setting can be set to zero by simultaneously pressing both selection keys (M. ) and (N. ). ­ The day and total counters only give the amounts in litres. Even if the amount at § 7. 3. 1 has been set in cups, jugs or us­gallons. GB Below a description is given of how operators with limited authority, after having entered the operators' PIN code, can read day and total counters, put these to zero and start the descaling programme. TIP ­ For the limited programming menu a operators' PIN code is required, see the fold out sheet at the back of these operating instructions. ­ Enter the operators' PIN code. The programme starts in the carousel (fig. 12 ) of the operators' menu at § 7. 2. 1, "Day counter coffee­making system". ­ When a wrong PIN code has been entered, wait a little while until the initial screen re­appears on the display. ­ Press the selection key (N. ) to go clockwise to the next setting (§ 7. 2. 8), see also fig. 12 . ECopyright Bravilor Bonamat B. V. version 1. 0 19 7. 2. 1 Day counter coffee­making system 7. 2. 2 Day counter hot water system GB G H I J D G H I J D K L M N K L M N Fig. 16 Day counter coffee­making system After entering the operators' PIN code fig. 16 appears in the display. The total number of litres that have been made that day can be read from the display. D Press the selection keys (M. ) and (N. ) simultaneously to set the day counter to zero. D Press selection key (M. ) to go the next setting or stop key (K. ) to leave the programming menu. Fig. 17 Day counter hot water system D Press, after having entered the operators' PIN code, selection key (M. ). ­ The total number of litres that has been made this day can be read from the display. D Press the selection keys (M. ) and (N. ) simultaneously to set the day counter to zero. D Press selection key (M. ) to go the next setting or stop key (K. ) to leave the programming menu. 20 version 1. 0 ECopyright Bravilor Bonamat B. V. 7. 2. 3 Starting descaling programme coffee­making system TIP ­ Stopping the programme Within 5 seconds (when the stop symbol above key (K. ) still flashes): D press key (K. ). ­ After 5 seconds (when the stop symbol key above key (K. ) has stopped flashing): D Hold programming key (G. ) down until fig. ­ The programme can still be left by pressing the red stop key. ­ After pouring in the descaler solution this is no longer possible!D Empty the coffee container through the tap (AB. ). D Press the confirmation key (L. ) to confirm that the container is empty. ­ A flashing hammer symbol appears on the display. ­ The waterreservoir is boiled empty and this water flows into the coffee container. [. . . ] Internal fuse has blown due to overload. 4. Coffee is too strong / not strong enough. Incorrect coffee dosage. Incorrect setting of the amount of water. Too much / too little coffee in the container. Incorrect setting of the amount of water. 6. [. . . ]