User manual BRAX X 1400

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual BRAX X 1400. We hope that this BRAX X 1400 user guide will be useful to you.

Lastmanuals help download the user guide BRAX X 1400.


Mode d'emploi BRAX X 1400
Download

You may also download the following manuals related to this product:

   BRAX X 1400 MANUAL 2 (676 ko)

Manual abstract: user guide BRAX X 1400

Detailed instructions for use are in the User's Guide.

[. . . ] Page 5 Connection of the Signal Cables . Page 5 Connection of the Speaker Cables . Page 7 Operation of the Circuit Control Cards . Page 7 Circuit Control Cards Data Sheet . [. . . ] The antenna connection is only activated if the control unit is switched ON. This ensures that, with the control unit switched off, the amplifier is also switched off to safe the battery. Fig. 2 4 5 1 2 3 1 Control lead (Remote) 2 Positive (+) 12V cable via fuse to battery 3 Ground cable 4 Positive (+) connection BRAX Power Stabilizer 5 Negative (-) connection BRAX Power Stabilizer Connection of the Signal Cables Front right The BRAX amplifiers have RCA connectors for cinch cables which are connected to the pre-amplifier outputs or line outputs of the control unit (tuner/radio). Ask your dealer for the appropriate BRAX accessories. Fig. 3 To Line Output Control Unit Rear right Rear left To Line Output Control Unit Front left 5 Connection of the Speaker Cables Important!Never connect the speaker cables to the vehicle chassis. Ensure that all the speaker systems are connected in-phase, i. e. The positive terminal is indicated on most speakers. In addition, the amplifiers may be operated in 2-channel mode (see Fig. The mono/stereo selector switch is located at the bottom of the amplifier. The function of the switch is described on a label at the bottom of the amplifier (see Fig. 5: 2-Channel Mode Mono Input Mono Input Position of selector switch at the bottom of the amplifier: Rear = Mono Front = Mono (see Fig. 6: 3-Channel Mode Mono Input Rear right Position of selector switch at the bottom of the amplifier: Rear = Mono Front = Stereo (see Fig. 7: 4-Channel Mode Position of selector switch at the bottom of the amplifier: Rear = Stereo Front = Stereo (see Fig. 4) 6 Circuit Control Cards The operating range of the amplifier is determined by replaceable Circuit Control Cards (CCC). If no special requirements regarding the CCC's are specified when ordering, the amplifier is supplied as standard with CCC 1. CCC 1 is plugged in at socket position 3 which means that the amlifier is operating in the full range (see list on page 8). If CCC 1 is inserted at socket position 1 or 2, as described in Fig. 8 to 12, the amplifier operates with a subsonic filter having a rate of change of 18 dB/Oct. The various Circuit Control Cards available are indicated in the list on page 8. Example: If you wish to use the module as a subwoofer amplifier, with the subwoofer being operated at 90 Hz, you find the corresponding Circuit Control Card from the list (in this case CCC 5) and insert the card in your BRAX amplifier at position 2 of that channel which is to control the subwoofer - the right channel in the case of the mono mode (bridge mode). Now the amplifier will only process frequencies up to 90 Hz, with any frequencies above that value being suppressed at the rate of change of 18 dB/Oct. At position 1 the amplifier will only process frequencies higher than 90 Hz. Handling the Circuit Control Cards Removal of a Circuit Control Card 1. [. . . ] 14 Selector Front Mono/Stereo With this selector the two front stereo channels can be changed to a mono channel. 10 Equipment Features and Control Elements 4 1 4 9 10 11 12 3 2 3 5 5 13 14 5 5 8 6 7 11 Technical Specifications X 1400 X 2400 Continuous power rating at 4 Ohm per channel . 4 x 100 Watts Continuous power rating at 2 Ohm per channel . 4 x 200 Watts Continuous power bridged into a 4 Ohm load . 2 x 400 Watts Total harmonic distortion (THD). [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE BRAX X 1400

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual BRAX X 1400 will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag