User manual BREVILLE BKC700XL

[. . . ] 4 6 8 9 10 12 14 18 18 18 19 20 21 22 23 24 24 26 27 27 28 28 28 28 30 32 34 36 Breville recommends safety first Know your Breville Gourmet Single Cup BrewerTM Operating your Breville Gourmet Single Cup BrewerTM - Installing the water filter - One-time priming process - Brewing a K-Cup® - Brewing with the My K-Cup® - Stopping the brew process - Brewing hot water - Refilling the water tank - Purging the brewer Menu and programming options - Setting the `CLOCK SET' feature - Setting the `ON-OFF TIME' feature - Setting the `AUTO OFF' feature - Setting the `BREW TEMP' feature - Setting the `BREW SIZE' feature Care and cleaning - Cleaning the brewer housing - Cleaning the K-Cup® holder - Cleaning the My K-Cup® - Cleaning the water tank and lid - Cleaning the water filter - Descaling the brewer - Storage Trouble shooting One year limited warranty French We at Breville are very safety conscious. We design and manufacture consumer products with the safety of you, our valued customer, foremost in mind. In addition we ask that you exercise a degree of care when using any electrical appliance and adhere to the following precautions: If the outlet is a standard 2-prong wall outlet, it is your personal responsibility and obligation to have it replaced with a properly grounded 3-prong wall outlet. Do not, under any circumstances, cut or remove the third (ground) prong from the power cord or use an adapter. [. . . ] Fill the Water Tank with water up to the 'MAX' mark on the viewing window. The Water Tank can be filled in two ways: a) Remove the Water Tank Lid and pour water directly into the Water Tank while it is still attached to the Brewer, then replace the Lid. B) Remove the Water Tank Lid, then gripping the handle located on the left side of the Water Tank, lift upwards. To stop brewing after the process has started, press and release the Power Switch on the right side of the Brewer to the `OFF' status. The flow of coffee, tea or hot cocoa will stop, the heating element will shut off and the LED's illuminating the Water Tank will no longer be lit. the LCD screen will indicate the time , `ON-OFF TIME' and `AUTO OFF'. None of the control panel buttons will be active until the Brewer is turned back on. If the Brewer has not been used for more than one week, you should renew the water from the inner tank by purging the brewer. If there is water in the Water Tank, remove the Water Tank Lid, then gripping the handle located on the left side of the Water Tank, lift upwards. NOTE: You must set the clock if using the `ON-OFF TIME' feature. The hour will blink, indicating the hour is ready to be set. If the hour has passed 12, the indicator switches from AM to PM. NOTE: If power is interrupted to the Brewer, the clock will need to be reset. Programmed brew size and brew temperature settings are remembered and restored automatically. All other settings will be restored automatically after the clock is reset. Once the appropriate hour is reached, press the `OK' button. This feature allows you to program the specific time when the Brewer will automatically turn on and/or off. By programming your Brewer to automatically turn on, you will not have to wait for the Brewer to heat the water in the Water Tank. It will take the Brewer approximately 3½ minutes to heat the water from room temperate. NOTE: You must set the clock if using the `ON-OFF TIME' feature. an alternative to setting the `ON-OFF TIME' feature is to leave the Brewer on all the time. We recommend this so your Brewer is always ready to brew a fresh cup of gourmet coffee, tea or hot cocoa. [. . . ] If `INACTIVE' is not displayed, follow the instructions, Setting the `ON-OFF TIME' feature (page 21) and Setting the `AUTO OFF' feature (page 23). The water level is low and a full cup cannot be brewed. After the 'Descaling the Brewer' process, ensure to disconnect the power plug from the wall outlet for at least 15 minutes, then re-plug the power plug into the wall outlet. The blue light in the water tank is flashing The LCD screen continues to indicate 'DESCALE' after completing the process. [. . . ]