User manual BRITAX B-NIMBLE

[. . . ] · Do not use stroller with a child taller than 44 inches (111. 8 cm). · Do not overload basket ­ Maximum weight in basket is 10 lbs (4. 5 kg). [. . . ] Failure to follow all warnings and instructions could result in serious injury or death. Infant. Car. Seat. Mode · The infant car seat adapters are ONLY compatible with Britax infant car seat and ONLY models from 2009 or newer · Attempting to fit them into another infant car seat can damage the car seat or cause the car seat to fall · Infant car seats MUST only be installed rear facing, or toward the parent. Installing the car seat forward facing can cause the stroller to become unstable. 3 Features Canopy. with. Sun. Visor Handles Carry. Locks Front. Wheels 4 · Actual product may vary from images. In the Box B-NIMBLE. Receivers Front. Wheels L R Britax. Infant. Car. Seat. Adapters Rain. Cover Cup. Holder 5 Assembly Unfolding the Stroller · Lift the chassis lock and pull the frame apart · Lift up on the handles and pull them away from each other WARNING: To avoid entrapment or pinching, do not fold or unfold when child is in or near stroller · Step down on the primary frame lock pedal to lock the stroller chassis IMPORTANT: Ensure that the stroller frame is locked before placing a child in the seat 6 Assembly Front Wheels · Locate the right and left wheels and ensure that the swivel lock lever is locked into place as shown before placing wheels on stroller L R · Press the wheel assembly onto the mount at the front of the stroller NOTE: Pull down on wheel assembly to ensure that it is locked R L Canopy · Line up the canopy mounts with the brackets on the frame and slide them down until they lock into place 7 Assembly Cup Holder · Slide the tab on the cup holder into the slot in the cup holder bracket Infant Car Seat Receivers · Place the infant car seat receiver behind the stroller frame and between the two brackets as shown TIP: The receiver should be pointing upward, and the raised lines (Fig. A) should be on the inside A · Slide and hold the top bracket up while closing the receiver around the frame and snapping it together NOTE: There is a left and right receiver Install as shown to ensure infant car seat allignment 8 Assembly Lowering the Infant Car Seat Receivers · Slide the receiver up to release the receiver · While holding the receiver up, rotate to the lower position 9 Operating Instructions Parking Brake · Step on the brake pedal on either side of the stroller until the wheels lock · Lift either brake pedal to release the brake Leg Rest Adjustment · Lift leg rest to raise it or press and hold both leg rest levers to lower 10 Operating Instructions Recline Adjustment · Lowering: From the back of the seat, press and hold the button on the recline adjuster and pull away from the seat back · Raising: Hold the adjuster strap and slide the recline adjuster to the desired position Swivel Wheels · Move the swivel wheel lock up to lock wheels in place or down to allow wheels to swivel 11 Operating Instructions Folding the Stroller · If infant car seat receivers are attached you must first rotate them to the lower position (Page 9) · Pull up on the carry strap to release the primary frame lock 12 Operating Instructions · Step on the secondary frame lock to release the chassis WARNING: To avoid entrapment or pinching, do not fold or unfold when child is in or near stroller · Push the stroller forward and continue folding until the chassis lock engages NOTE: You may need to compress the stroller to engage the chassis lock 13 Securing Your Child · Unlatch the harness by depressing the button in the center of the buckle while pulling the two tongues away from the buckle assembly · To raise or lower the harness height, disconnect the buckle tongues and pull the harness strap out from the back of the seat · Rethread the strap at the desired height and reconnect the buckle tongues (see next page) NOTE: Harness height should be at or above the shoulders of the child 14 Securing Your Child · Buckle the harness by inserting the tongues on the harness straps into the buckle assembly NOTE: Ensure the straps are not twisted as they may become uncomfortable for the child · Tighten or loosen the harness straps by sliding the harness adjusters up or down To reconnect buckle tongues, line up the two pieces and slide the upper portion onto the track on the lower piece 15 Infant Car Seat Mode Attaching Britax Infant Car Seat Adapters · Slide each of the adapters under the infant car seat handle and into the shell until they click into place NOTE: There is a left and right adapter and orientation should be as shown · Pull downward on the adapter to ensure that it is secure Removing Britax Infant Car Seat Adapters · Pull the release lever and slide the adapters down and out of the infant car seat shell 16 Infant Car Seat Mode Attaching the Infant Car Seat NOTE: Seat back should be reclined completely (Page 11) · Line up the locking latches on the infant car seat with the sockets on the infant car seat receivers · Press down until the adapters lock into place IMPORTANT: Infant car seat must be installed rear-facing ONLY Removing the Infant Car Seat · Lift the release levers on both adapters and lift the infant car seat away from the stroller 17 Rain Cover 18 Care and Maintenance Parking. Brake. · Periodically check that the parking brake works properly and locks both wheels securely . · Clean out any dirt or debris that may prevent the brake from working . · Wipe the frame with a damp cloth and mild soap . Use clean, dry cloth or towel to wipe away excess water and soap . Frame. Fabric · Do not machine wash, dry or iron the cover . · Hand wash with cold water and mild soap . [. . . ] PLEASE COMPLETE AND MAIL THE REGISTRATION CARD WITHIN 30 DAYS OF PURCHASE, OR VISIT WWW. BRITAXUSA. COM/REGISTRATION. Warranty. Limitations This warranty does not include damages which arise from negligence, misuse, corrosion, or use not in accordance with the user guide . [. . . ]