User manual BRITAX WIZARD

[. . . ] Wizard User Guide Table of Contents Safety Information . 10-11 Rear Facing Lap-Shoulder Belt Installation . 12-13 Rear Facing Lap Belt Installation . 16-20 Forward Facing LATCH Installation . [. . . ] · When not in use, always store the LATCH connectors in storage pouches sewn in cover above rear facing lock-offs. 1 Place the child restraint forward facing A on the vehicle seat. · Restraint must be in the full upright position when installed in forward facing mode with children over 33 pounds (15kg). · If installing with Versa-Tether®, remove tether from pouch and loosely attach to an approved tether anchorage point before continuing. See pages 23­25 for complete Versa-Tether instructions. 5 Remove slack from the lap portion of the vehicle belt. 6 Push the child restraint firmly into the vehicle seat while pulling the shoulder D portion of the vehicle belt tightly through the lock-off to remove slack (Fig. 7 Hold the shoulder belt tight, then rotate the lock-off upward until it clicks in place (Fig. E). · Lock-off is not engaged and vehicle belt is not secured until a click is heard. 2 Pull the vehicle belt out, then pass it over the LATCH bar, through the forward facing belt slots, then over the LATCH bar on the other side (Fig. 3 Verify that the vehicle belt is not twisted, then buckle (Fig. C). B 8 Verify that the vehicle belt is tight and the child restraint is secure. · See Checking Buckle Position on page 26. · Installation can be improved by the use of the Versa-Tether® (see pages 23­25). E Removal: Open lock-offs, then unbuckle and remove vehicle belt from belt path. Disconnect Versa-Tether®, if attached. C 18 19 Installation: Forward Facing Forward Facing Lap Belt Installation Switching the LATCH Connectors If the LATCH connector will not properly connect to the LATCH bar in the vehicle, the connectors must be switched from one side to the other. This will ensure that the connectors are correctly aligned. 1 Lift the front of the cover to access the LATCH bar. 2 Slide one connector through both rear D facing belt slots to the opposite side of the restraint, so that both connectors are on the same side of the restraint (Fig. 3 Loosen the loop on one connector (Fig. 4 Thread the other connector through the loop created in step 3 to switch positions (Fig. 5 Slide the connector which is now closest to the front of the restraint through both rear facing belt slots to E the opposite side of the restraint, so that each connector is in proper position on the LATCH bar. 6 Replace cover and continue with installation procedure. · Figure A illustrates the forward facing lap belt only vehicle belt route. · When not in use, always store the LATCH connectors in storage pouches sewn in cover above rear facing lock-offs. 1 Place the child restraint forward facing on the vehicle seat. A · Restraint must be in the full upright position when installed in forward facing mode with children over 33 pounds (15kg). · If installing with Versa-Tether®, remove tether from pouch and loosely attach to an approved tether anchorage point before continuing. See pages 23­25 for complete Versa-Tether instructions. 2 Pull the vehicle belt out, then pass it under the LATCH bar, through the forward facing belt slots, then under the LATCH bar on the other side (Fig. 3 Verify that the vehicle belt is not twisted, then buckle. 4 Push the child restraint firmly into the vehicle seat while removing slack from the vehicle belt (Fig. [. . . ] 2 Locate the metal buckle strap retainer on bottom of the restraint. 3 Pull retainer away from child A restraint to loosen. 4 Turn the retainer so that the short side will go through the slot in the restraint shell (Fig. 5 Push the retainer through slots in the shell and cover, to the front of the restraint. Care and Maintenance Cleaning the Buckle The buckle will need to be periodically checked and cleaned of any accumulated debris, dirt, or dried liquids. [. . . ]