User manual BROTHER PT-2600

[. . . ] 2600/2610 USER'S GUIDE GUA DE USUARIO Read this User's Guide before you start using your P-touch. Keep this User's Guide in a handy place for future reference. Antes de usar su equipo por primera vez, lea cuidadosamente esta gua de usuario. Guarde esta gua de usuario para futuras referencias. INTRODUCTION Thank you for purchasing the P-touch 2600/2610! [. . . ] The new block mark ( indicate the end of the block. EXAMPLE ) appears in the text to To add a new block: 1: K ' s bar_ q Hold down c and press _ once. 1: K ' s 1: _ bar 49 TZ -Ta pe -La AV be l TAB FUNCTION This function allows you to separate sections of a line of text by adding tabs. This enables you to create perfectly aligned columns without having to type in several spaces. All tabs have the same length and are measured from either the beginning of the line or the previous tab, if there is more than one. The tab length can be set between 0. 0" and 11. 8" (0. 0 and 30. 0 cm). The text cannot contain more than 50 tabs. If the maximum number of tabs has already been added to the text when c is held down and Q is pressed, the error message "TAB LIMIT!" appears. To set the tab length: 1 2 Hold down c and press W once. Press e or h until the desired length is displayed or use the number keys to type in the length. 3 To change the units (inches or centimeters) used to display the tab lengths, press M until the desired units are displayed. Press _. The tab mark ( ) appears in the text to indicate the position of the tab. If the text in front of a tab extends past the point where the next section of text should start, the text will instead start at the following tab position. For example, if the tab length is set to 1. 2" (3. 0 cm) and the following text is typed in: To add a tab: q 1: A B C D E F G H I 2: J K L M N O P Q R S T U 50 The label shown below will be printed. Margin Tab (1. 2" (3. 0 cm)) Tab (1. 2" (3. 0 cm)) Margin EXAMPLE To set the tab length to 1": 1 Hold down c and press W once. TAB LENGTH 2. 0inch 2 Press h until 1. 0 is displayed. TAB LENGTH 1. Oinch 3 Press _. To add a tab: q Hold down c and press Q once. 1: a r t NO. _ 51 TZ -Ta pe -La AV be l DELETE KEY The Delete (backspace) key ( * ) allows you to remove characters to the left of the cursor's current position. It differs from the left cursor key ( f ), which only moves the cursor without deleting any characters. The delete key can also be used to quit most functions and return to the previous display without changing the text. Some questions asking you to confirm a command may appear on the LCD display, especially when the function that you have chosen will delete or affect files. In these cases, pressing * is like answering "no". 1 To answer "yes", press _. Press f, w, e or h to position the cursor below the character immediately to the right of the character that you wish to delete. Press f, w, e or h to position the cursor below the character immediately to the right of the last character that you wish to delete. Hold down * until all of the characters that you wish to delete are deleted. Press *. e l To delete one character: 2 To delete a sequence of characters: 1 2 To quit a function without changing your text: q To answer "no": q TZ p -Ta -La AV be LINE OUT FUNCTION With the Line Out function, you can easily remove an entire line of text. To delete a line of text: 1 Press f, w, e or h to position the cursor within the line of text that you wish to delete. 52 2 Hold down c and press P once. Each time Pis pressed while c is held down, one line of text is deleted. EXAMPLE To delete "012-345-6789": 1: G a r d e n 2: 3 4 5 6 7 8 9 _ q Hold down c and press P once. 1: K ' s 2: _ Garde TZ p -Ta e -La AV be l CLEAR FUNCTION When clearing the display before entering new text, the Clear function can be used to choose whether all of the text is erased and all format functions (Font, Size, Width, Style, Underline, Frame, Tape margin (for TZ tape only), Alignment, Tab length, Mirror printing (for TZ tape only), and Length (for TZ tape only)) are returned to their default settings, or whether just the text is erased. To delete all of the text and return all formats to their default settings: 1 2 Hold down c and press *. [. . . ] only): $8. 75 Overnight Delivery (Continental U. S. orders $ $ Method of Payment (check one) ( ) Visa ( ) Master Card ( ) Discover ( ) Check/Money Order ( ) American Express Account Number Expiration Date Signature Billing Address (if different from shipping address at left) PT-2600/2610 CONTACT INFORMATION (For USA Only) Service Center Locations If you need a local service center, please call 1-800-284-HELP (4357) to locate the authorized service center closest to you. Note: Be sure to call the Service Center before your visit. Service centers do not provide operational assistance. [. . . ]