User manual BSS FDS366T

[. . . ] FDS-366T OMNIDRIVE User Manual Connect here first. . . TM FDS-366T ZM10019 issue 4 CB/PW/DN/DP/JWK Software version 2. 00 IMPORTANT SAFETY INFORMATION DO NOT REMOVE COVERS. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. THIS EQUIPMENT MUST BE EARTHED. IT SHOULD NOT BE NECESSARY TO REMOVE ANY PROTECTIVE EARTH OR SIGNAL CABLE SHIELD CONNECTIONS TO PREVENT GROUND LOOPS. ANY SUCH DISCONNECTIONS ARE OUTSIDE THE RECOMMENDED PRACTISE OF BSS AUDIO AND WILL RENDER ANY EMC OR SAFETY CERTIFICATION VOID. REGULATORY INFORMATION This equipment has been tested and found to comply with the following European and International Standards for Electromagnetic Compatibility and Electrical Safety: Emmissions (EU): Generic Immunity (EU): Mains Harmonics (EU) Voltage Fluctuations (EU) Electrical Safety (EU): Electrical Safety (USA): EN55013+A12+A13 EN50082-1 EN61000-3-2 EN61000-3-3 EN60065+A11 UL813/ETL (1990) (1992) (1995) (1995) (1993) (1996) For continued compliance with international EMC legislation ensure that all input and output cables are wired with the cable screen connected to Pin 1 of the XLR connectors. [. . . ] To highlight the Store type message, use the navipad 'v' key while a program number is highlighted. Once highlighted, turn the rotary encoder to select the type of store you wish to use. INT This stores the program in the internal memory of the unit. Prg This stores the currently selected program to a PC card (if inserted) in the slot at the front of the unit (in a 366T file format). All This stores all program data to a PC card (if inserted) in the slot at the front of the unit (in a 366T file format). The Program Lock can be applied to a program stored using any of these 3 methods. NOTE: The edit flag ('*') appears when there are unsaved changes to a program, compared to the initial status of the last recalled/stored program (Internal memory only). When a program is stored to internal memory, the edit flag will disappear. If a program is stored to a PC card, then the flag will NOT disappear, since there are differences between the last recalled/stored program (Internal), and the current program. Store Lock Once the program name has been entered, the store type selected, and the Program lock status cleared, pressing the STORE key again will prompt the message "Store Locked?", asking whether the program should be stored with a Program lock. Use the rotary encoder to turn the Lock on or off ("Locked?" or "Unlocked?"). Once the Lock status is set, push the STORE key a final time to commit the program to memory (or PC storage). The display will now default back to the screen displayed before the STORE facility was accessed. To exit from the store screen without storing a program, press the 'RECALL' button. - 50 - FDS-366T Program Functions Delete Program To delete a program press the UTILS button and scroll through the options until the screen on the left is displayed. To enter the Delete Program mode, press either > or turn the encoder clockwise, this will change the screen to: Choose the program to be deleted using the < and > keys or rotary control. Pressing the ^/v keys at any time will exit the Delete Program mode. Note: Program locked (key symbol) and Owner locked (padlock symbol) programs can both be deleted using Delete Program. OEM locked (diamond symbol) programs can also be deleted using Delete Program unless the Delete Program option was locked in the Utilities during the OEM lock process. In this case the OEM program cannot be deleted if it is the currently active program but, can still be deleted if another program is selected. To totally secure the unit with OEM programs both the Delete Program and Configuration parameters must be locked on every program. If this is not done then a user could create a new unlocked program by changing the Configuration and this would then give access to Delete Program again. - 51 - FDS-366T 17. 0 PC Card Usage Card types The program memories of the FDS-366T Omnidrive can be saved to PC cards for further storage, safety backup and portability between systems. Note that the PC card only inserts up to about a third of its length into the front panel slot. Do not try to force the card further in as this could cause damage to the unit. Also it is recommended not to leave unused cards in the slot as they could become damaged if the unit is knocked from the front. Compatible Cards The PC Card socket on the front of the unit is designed to use PCMCIA type 2 memory cards of between 256kbyte and 2Mbyte storage capacity. [. . . ] Solution: Check power cable is inserted properly at back of unit. Check the fuse in the plug (if existing) on the power cable and/or try another power cable. Check mains supply is powered and operating at a voltage within the required range. Check the fuse at the rear of the unit has not blown. Problem: No output. [. . . ]