User manual BT CONVERSE 2200

[. . . ] User Guide This new interactive user guide lets you navigate easily through the pages and allows you to be directed straight to any websites that are referenced. Simply hover the cursor over the page number or website reference and click when the changes to the icon. BT CONVERSE 2200 Welcome to your BT Converse 2200 Corded Telephone · Eleven one-touch buttons for easy dialling of your most important numbers. · Headset facility lets you make and receive calls privately while keeping your hands free. · Handsfree button lets you make and receive calls over the built-in loudspeaker and microphone. [. . . ] Press again to return to your caller. Handsfree Make and receive calls without lifting the handset. When your call is answered, speak as normal (or if you wish to speak to your caller privately, pick up the handset). Press to end the call. Receiving a call handsfree 1. Press to end the call. Message waiting If your BT Converse phone is connected to a switchboard, the message waiting indicator will flash when you receive new voicemail messages. BT 1571 or similar network voicemail users can also use this feature, however the indicator light will not flash. New voicemail messages will be indicated by a stuttered dial tone when you pick up the handset. If you experience any problems, please visit www. bt. com/producthelp Using the phone 9 Message waiting switch If your telephone is connected to a switchboard you may need to change the message waiting switch setting on the base of the phone. It is pre-set to MW3 which is for an SX2000 switch. MW1 and MW2 positions are for when the telephone is connected to an ISDX switch. If the switch is moved to MW2 and the message waiting indicator stays on permanently, use MW1. 1. Lift the handset, or press your answering service. and dial to connect to If in doubt, please refer to your PBX instructions/manager for the correct procedure to access this service. Set the Ringer Volume switch on the underside of the phone to 0 (Off), 1 or 2. Adjusting the ringer tone 1. Set the Ringer switch on the underside of the phone to 1 (Low), 2 (Medium) or 3 (High). R (Recall) The button is used to access a range of switchboard services, for example, to transfer calls and with some BT Calling Features. Press to switch the earpiece/headset volume to High. After you hang up, the volume will automatically return to Normal volume. If you experience any problems, please visit www. bt. com/producthelp 10 M1 ­ M11 memory buttons Each number can be up to 32 digits long and can include a pause or #. If you enter more than 32 digits you will hear an error beep. You can store your 11 most frequently used phone numbers on the grey one-touch memory buttons that are located on the right hand side of the product and dial them by pressing a single button. Buttons 7-11 have been pre-programmed with the following BT Services, however you can overwrite them with your own numbers. M7 = Residential Directory Enquiries 118 500, M8 = Business Directory Enquiries 118 700, M9 = BT Answer 1571, M10 = Call Divert On, M11 = Call Divert Off. One touch memory label One touch memory buttons To enter a pause when storing a number press . To cancel while storing, hang up the handset . Any number already stored or press will be kept. Store/replace a one touch number 1. Press and hold the grey one touch button that you want to store a number under. Release the button when you hear the dial tone stop. and listen for Service Directory Enq's (residential) Directory Enq's (business) BT Answer Call Divert On Call Divert Off Number 118500 118700 1571 1571 #21# *21* Please note Call Diversion services may allow other divert options. Check with your network provider for details. If you experience any problems, please visit www. bt. com/producthelp Using BT Calling Features 13 Switch Call Diversion off 1. Lift the handset, press the Call Diversion Off one-touch memory button (button 11). [. . . ] · All items of telephone equipment have a Ringer Equivalence Number (REN), which is used to calculate the number of items which may be connected to any one telephone line. If the total REN of 4 is exceeded, the telephone may not ring. · With different telephone types there is not guarantee of ringing, even when the REN is less than 4. Declaration of Conformance Hereby, A-Team declares that this BT Converse 2200 is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. If you would like a copy of the Declaration of Conformance, go to the product website at www. bt. com/producthelp Product disposal instructions The symbol shown here and on the product means that the product is classed as Electrical or Electronic Equipment and should not be disposed with other household or commercial waste at the end of its working life. [. . . ]