User manual BT QUARTET 1100

[. . . ] Quartet 1100 Cordless Telephone User Guide This equipment is not designed for making emergency telephone calls when the power fails. Alternative arrangements should be made for access to emergency services. This product is intended for connection to analogue public switched telephone networks and private switchboards in the United Kingdom. Please open this page for an `at a glance' guide to your Quartet 1100 Please open this page for a further `at a glance' guide to your Quartet 1100 At a glance Aerial Can be extended. In Use/Battery Low light Indicates when the handset rings, is in use or, if the handset battery needs recharging. ry Low tte Ba In u se M1/M2 buttons Allows you to store and dial one touch numbers. M1 M2 Volume control buttons Adjusts the handset ringer and earpiece speech volume. Talk button Press to make or receive a call. v w AB Ch an ne l Channel button Selects an alternative radio frequency if interference occurs during a call. Keypad DE C 1 GH 2 5 I 3 6 9 4 Quickdial button Allows you to store and dial up to 10 numbers in the memory. [. . . ] You cannot page the handset while it is being used on a call. An incoming call will override a page call and the handset will ring as normal. If additional handsets are registered to the Quartet 1100 base unit then all handsets will ring when paged. To page the handset Page Press the PAGE button on the base unit. You can stop paging at any time by pressing the PAGE button on the base unit or any buttons on the handset. Pressing the TALK button will not only stop the paging but also seize the line. Press the TALK button a second time to clear the line. After approximately one minute your handset will return to standby. 1471 (Call Return) By pressing the 1471 button you can hear the telephone number of the last person who called you. You also have the option to return the call. To use the 1471 button Press the TALK button and wait for the dialling tone. 1471 Press the 1471 button. You will hear the telephone number of the last person who called you. If the caller withheld their number the time of the call is still stored but not the number. You also have the option to return the call. 16 Call Waiting Note To use Call Waiting you will need to subscribe to the Service from your network provider. If an incoming call arrives while you are already engaged on a telephone call, you will hear a soft beep every 5 seconds (this beep is not audible to the person you are speaking to). Instead of the engaged tone, the second caller will hear an announcement to hold as you are aware that there is a second call. To use Call Waiting R You can answer the second call, without disconnecting your first caller, by pressing the R button. When you have spoken to the second caller you can return to the first caller by pressing the R button again. You can switch back and forth between the 2 calls without disconnecting either if you wish. If you wish to disconnect the first call, press the TALK button after speaking to the first caller. Press the TALK button again and continue with the second caller. The second caller will only be charged for their call from the moment you answer and not while they are waiting for your initial contact. R 17 Using Quartet 1000 Additional Handsets You can buy and use up to 3 Quartet 1000 additional handsets with your Quartet 1100 to extend your phone system, without needing to install extension sockets for each new phone. Each additional handset is supplied with its own charger and user instructions, but the following information will tell you how to register and use an additional handset with your Quartet 1100. Note You must charge your additional handset for 24 hours before registering it. To register an additional handset Place the handset you wish to register on the base unit and then remove it. Page Press and hold the base unit PAGE button for 5 seconds until both the POWER/IN USE light on the base unit and the IN USE/BATTERY LOW light on the handset begin to flash. Release the PAGE button and press the TALK button on the handset. Your additional handset is registered automatically and you will hear a long confirmation beep and the IN USE light will stop flashing. Page Registering your handset You must register your Quartet additional handset before it can be used with your Quartet base unit. [. . . ] See page 22 for more information on switchboard use. See page 22 to change to pulse dialling. Use the PBX access code. · Handset does not ring and there is no IN USE light on handset. Handset battery pack is discharged. Place the handset on the base unit and recharge it for 24 hours. · Handset does not ring, but IN USE light show on handset. The handset ringer may be set to its minimum setting. Increase the handset ringer volume. 24 · Base unit does not ring but lights show on base unit. Telephone is not connected to the telephone line. The base ringer is set to off. Plug the telephone into the telephone socket. Set the base ringer setting to a higher volume. Try the telephone on another socket or another line. [. . . ]