User manual BUFFALO HS-DHTGL : TERASTATION LIVE

[. . . ] User Manual TeraStation Live HS-DHTGL/R5 www. buffalotech. com v1. 0 Introduction Congratulations on your new TeraStation!This user manual is intended to assist you in configuring it. Because we're constantly updating our product, the images and text in this manual may vary slightly from the images and text displayed by your TeraStation. These changes are minor and should not affect the ease of setup adversely. [. . . ] Click on its name under USB Disk Setup to begin. 36 Advanced Settings Disk Management (USB hard drive setup) From here you can see your USB hard drive's setup information. If the hard drive's information isn't displayed properly, try restarting your USB hard drive and then restarting your TeraStation. Some USB hard drives must be reformatted from within TeraStation before they can be assigned shares. Press Format USB Disk, or choose Disk Format from the left-side menu, to begin reformatting your USB hard disk. Turn to page 39 for more information on reformatting disks. Turn to page 40 to set up shares on your USB hard drives. 37 Advanced Settings Disk Management (Disk Check) To initiate a comprehensive disk check on a hard drive or array of drives, select the hard drive or array that you want to check from the Target dropbox and click the Start Disk Check button. Performance will be slower while the disk check is running. 38 Advanced Settings Disk Management (Disk Format) To format a hard drive or array, select it from the Target Disk drop box. Choose the file system desired from the File System dropbox (internal drives can only be formatted with XFS). Note that FAT32 has a 2 gigabyte single file size limit. If you choose FAT32 for your file system, you will not be able to store single files larger than 2 gigabytes on the drive. Use of the XFS or EXT3 file systems is recommended. Depending on the size of the target hard disk or array, a Disk Format may take several hours to complete. Performance will be slow during the disk format. 39 Advanced Settings Shared Folders To add new shares to your TeraStation, select Shared Folders from the left side menu, and then click the Add button. To delete a share, select the share you'd like to delete, and press the Delete button. Deleting shares will remove the share and erase all of the files and folders inside that share. 40 Advanced Settings Add a new Shared Folder To add a new shared folder, enter a name for it in the Shared Folder Name box and choose which Disk Space it will reside in. You may also choose which operating systems and features the share will support by putting the appropriate checks next to Shared Folder Support, and whether the share supports the Recycle Bin by putting a selecting Enable or Disable. Enter a Shared Folder Description and a Remote Backup Password if desired. Click Apply to build the new shared folder. Appletalk support is available for use with legacy Macs. Checking "Apple" by Shared Folder Support lets you use your TeraStation with older Macs, but gives you all of Appletalk's limitations, including a 2GB maximum filesize and a 32 character limit for filenames. For OS X 10. 3. 9 and later, leave "Apple" unchecked for best performance. Remote Backup Password will set a password on this share for other TeraStations who want to use it as a remote backup target. [. . . ] Cannot communicate with SATA chip (IC1). Cannot communicate with SATA chip 2 (IC2) Cannot communicate with USB chip (IC5) Cannot communicate with Ethernet chip (IC13) Cannot mount HDDx HDDx faulty (HDDx is excluded from raid because of errors) Sound A A A A A B B B B B B A A A A A B B 74 Replacing a Hard Drive Turn the key counter-clockwise to open drive door. Squeeze the tabs gently and swing the tray latch upward. The hard drive tray will now slide out. 75 Lower the drive carefully to the work surface. Gently push down on the two tabs to release the plug. 76 Pull the plug straight out to remove the drive. To remove the hard drive from its cage, set the assembly on a soft surface and remove these four screws. 77 Install a new hard drive by doing the same steps in reverse order: Begin by screwing the new hard drive into the cage. Plug the power/data connector into the hard drive. Slide the hard drive cage back into the TeraStation. Press the latch down to lock the hard drive cage in place. 78 Technical Specifications LAN Standards: Transmission Types: Access Media: Media Interface: USB Standard: IEEE 802. 3u 100BASE-TX; IEEE 802. 3 10BASE-T 1000Mbps/100Mbps/10Mbps; 100BASE-TX 4B/5B, MLT-3;10BASE-T Manchester Coding CSMA/CD RJ-45 USB 2. 0 Hi-Speed (HS) Full-Speed (FS) Low-Speed (LS) USB A Connector (2) Max: 480 Mbps (HS Mode) Max: 12 Mbps (FS Mode) ~56W (Varies based on size) 6. 7" x 9. 3" x 12. 2" (170 x 235 x 310 mm. ) ~15. 8 lb. (7. 2 kg. ) (Weight varies based on size) 32° - 95° F; 20-80% non-condensing 79 USB Connector: Data Transmission Speed: Power Consumption: Dimensions: Weight: Operating Environment: Contact Information (North America) Buffalo Technology USA Inc. [. . . ]