User manual BUFFALO WZR-G300N : WIRELESS-N NFINITI BROADBAND ROUTER AND ACCESS POINT

[. . . ] User Manual - AirStation Draft-N WZR-G300N Nfiniti Wireless Router & AP www. buffalotech. com v. 1. 00 Table of Contents Introduction . 28 2 Table of Contents DHCP Server . 87 4 Introduction Work and play - further and faster! [. . . ] IEEE802. 11g/b Standard for Wireless LANs; 125* High Speed Mode also Available (Turbo G). Host Operating System Microsoft Windows® 98SE/ME/NT4. 0/2000/XP, Unix, Linux and MacOS Media Access Protocol Wired - CSMD/CD (Collision Detection) Wireless - CSMD/CA (Collision Avoidance) with Acknowledgment (ACK) 60 Specifications AirStation IEEE 802. 11 Channel Sets The range of the wireless signal is related to the Transmit Rate of the wireless communication. Communications at a lower Transmit range may travel longer distances. Center Channel ID FCC 1 2412 2 2417 3 2422 4 2427 5 2432 6 2437 7 2442 8 2447 9 2452 10 2457 11 2462 11 default channel 61 Troubleshooting Common Problems · · · · Out of range, client cannot connect to the AirStation. Configuration mismatch, client cannot connect to the AirStation. Absence or conflict with the Client Driver. Conflict of another device with the AirStation hardware. LED Activity Monitoring LED activity helps identify problems. · Power LED should be Green, · Wireless LED should be Green if the line is active. If is it blinking Green, wireless communication is active. · Ethernet LED should be Green (100Mbps) or Amber (10Mbps) while the communication is active. · The Red Diag LED will flash during boot and firmware updates. DIAG LED Activity Unplug the power for three seconds. Plug the power back in to monitor the Diag LEDs during start-up. 62 Troubleshooting DIAG LED Activity Table DIAG LED Display Continuous Red Red flash, 3 times Red flash, 4 times Time Starting Starting Starting Description/Action RAM Error Red flash, 2 times Starting Flash ROM Error A problem on the wired LAN side A problem on the wireless LAN side LEDs Work But Client PC Cannot Connect to Network If the LEDs indicate that the network is working properly (Power LED is on, Transmit/ Receive LED blinks), check the TCP/IP settings of the network. Changing Client TCP/IP Settings in Windows Consult the LAN Administrator for correct TCP/IP settings. Double-click on the Network icon to view Network Properties. From the list of installed components, verify the TCP/IP => wireless LAN adapter protocol is installed. 63 Troubleshooting · If the wireless adapter protocol is not yet installed, click the Add button and select the TCP/IP protocol from the list. Refer to Windows Help for more information. · If the wireless adapter protocol is installed, select the protocol and click the Properties button. Verify that the parameters match the settings provided by your LAN Administrator. Make changes if necessary, and click OK. If prompted, restart your computer. Other Problems Please refer to www. buffalotech. com for further reference materials. 64 Configuring a WDS Bridge Your AirStation's WDS bridging capability allows you to extend the size of your wireless network by adding additional AirStations, all connected wirelessly. In this simple example, we'll connect two AirStations in a wireless bridge. You may use these same steps to add additional bridges for greater coverage. * For easiest configuration, we recommend configuring all components in close proximity before deploying them to their final positions. Wired connections make initial configuration even simpler. [. . . ] ·Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ·Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. [. . . ]