User manual BUSHNELL IMAGEVIEW 111545 4-10

[. . . ] Magnify capture save 5M P C a M e r a w i t h 22x M ag n i f i C at i o n D i g i ta l s p ot t i n g s co p e User Manual Model: 111545 Lit. #: 98-1411 / 04-10 Parts and Controls Guide (K) remote Jack (L) usB Port (M) Card slot (G) lCd display (D) oK/PlaY Button (E) snaP Button (C) up/down arrow Keys (J) diopter adjustment (H) Power led (N) Zoom setting (A) on/oFF (B) Menu Button Button (O) Focus Knob (F) eyepiece/Camera select slider (I) Battery Compartment 2 QuiCK start Guide 1) To use the ImageView as a standard spotting scope, attach it to a tripod (a small one is included), set the slider (F) to the "Eyepiece" position, and look through the eyepiece (the rubber eyecup may be rolled down if you wear glasses). The eyepiece diopter adjustment (J) index dot should be set to the "0" position. Aim the scope at your subject and adjust the focus knob (O) until it appears sharp. [. . . ] Point the scope at a distant object (preferably one containing fine detail such as a tree or sign), and adjust the focus knob (O) until it appears as sharp as possible on the display. If you would like to explore the various available options, see the manual section titled "The Capture and Setup Menu-Options and Settings" for directions regarding how to select and change settings such as resolution, image quality and exposure. When the Eyepiece/Camera select slider is in the "Eyepiece" position, the image formed by the front (objective) lens is directed to the eyepiece rather than the digital camera sensor, so the LCD display will not let you see the "live image". The scope's zoom eyepiece provides optical zoom from 15x to 45x magnification, while the camera's magnification is fixed at approximately 22x. If you want to preview the framing of your subject as you are looking through the eyepiece prior to taking a photo, rotate the zoom ring so that the green dot is opposite the red index dot (this sets the eyepiece to about 22x magnification). When you are ready to take a photo, be sure to move the select slider over to "Camera"otherwise your photo will be partially or entirely black. And you will then be able to use the LCD display for preview and review as you take photos. Although the snap button on the scope may be used to take photos, it is highly recommended that you plug the supplied remote shutter cable into the remote jack (K) to obtain the steadiest results (press the 2. 3. 4. 9 taKinG still PHotos 5. The display will "freeze" briefly immediately after a photo is takenthis is normal while the image is being stored in the internal or card memory. The "remaining photos" counter in the lower right corner of the display will drop by one number after each photo (or two, depending on your subject and settings) is taken. Once it reaches "00", and the display indicates "MEMORY FULL" when snap is pressed, you are out of memory (storage space) and will need to download the photos you have taken so they can be deleted to make room in the memory for new photos, or you may remove the filled up card and install another SD card if you are on a trip away from your computer. Press the Up arrow key to zoom in (you will see the result on the LCD, and the digital zoom indicator increases in 0. 1x increments up to 4. 0x ). Press the Down arrow key to zoom back out (the zoom indicator decrements down). To turn off all digital zoom (go back to the 22x optical magnification only) keep pressing the Down key until the zoom indicator goes back down all the way to "1. 0x" and disappears. To review a photo after you take it, press the oK/plaY button. To see previous photos, press the Down arrow key-each press takes you back one photo, and pressing the Up arrow key moves forward to more recent photos. Press the oK/plaY button again to return to the live preview. See the section "The Play Menu-Options and Settings" for directions covering deleting photos, formatting internal or card memory, and protecting important photos. 6. 7. NOTE: Use care during handling to avoid touching the exposed lenses of the ImageView spotting scope to prevent degrading the image quality. Clean the lenses only with camera lens cleaning tissue or microfiber cloth, after removing loose dust or dirt with a blower brush or "canned air". Camera lens cleaning fluid may be used if necessary (lightly moisten the lens tissue, do not apply directly to the lens), avoid the use of other liquids of any type. 10 sHootinG Videos shooting Videos (setting/Using Video Mode) To switch from still photo to video mode, hold the SNAP button down for 2-3 seconds, until a beep is heard. The video mode icon (a frame of movie film) will appear at the top left corner of the LCD. [. . . ] Select "One" , then press OK to protect the currently displayed photo, select "All" and press OK to protect all stored photos. Select "One" or "All" and press OK a second time to "unprotect" one or all photos if you later want to delete them. Protect one, All 19 TWO-Year LIMITeD WarraNTY FCC Compliance Statement: Your Bushnell® product is warranted to be free of defects in materials and workmanship for two years after the date of purchase. In the event of a defect under this warranty, we will, at our option, repair or replace the product, provided that you return the product postage prepaid. This warranty does not cover damages caused by misuse, improper handling, installation, or maintenance provided by someone other than a Bushnell Authorized Service Department. [. . . ]