User manual BUSHNELL TROPHY CAM 119425C

[. . . ] TROPHY CAMTM INSTRUCTION MANUAL Model#: 119425C Lit# 98-1573/02-10 IMPORTANT NOTE Congratulations on your purchase of one of the best trail cameras on the market!Bushnell is very proud of this little unit and we are sure you will be pleased with it as well. We appreciate your business and want to earn your trust. Please refer to the notes below and the instructions in this manual to ensure that you are completely satisfied with this product. [. . . ] Try different distances and angles from the camera. · If the motion indicator LED light blinks, it indicates that position can be sensed. If it does not blink, that position is outside of the sensing area. The results of your testing will help you find the best placement when mounting and aiming the Trophy Cam. The height away from the ground for placing the device should vary with the animal size appropriately. You can avoid potential false triggers due to temperature and motion disturbances in front of the camera by not aiming it at a heat source or nearby tree branches or brush (especially on windy days). Switching ON the Camera Once you switch to the ON mode, the motion indicator LED (red) will blink for about 10 seconds. This gives you time to close and lock the front cover of the Trophy Cam and then walk away. During this time, the motion indicator LED will blink red continuously. After it stops blinking, the PIR is active, and any motion that is detected by it will trigger the capture of photos or videos as programmed in the SETUP Menu. Be sure you have read the descriptions of the Capture Number, Video Length, Interval 20 and Sensor Level parameters. Please note, the PIR is strongly sensitive to ambient temperature. The greater the temperature difference between the environment and your subject, the farther the possible sensing distance. The average sensing distance is about 45 ft. Before leaving the camera unattended, please check for the following: · Are the batteries or DC power supply inserted/connected with correct polarity and is the power level is sufficient?· Does the SD card have sufficient available space and is its writeprotection (lock) switch off?· Is the Power switch in the ON position?(do not leave it in SETUP). PLAYING BACK/DELETING the PHOTOS/VIDEOS After you have setup, mounted and activated your Trophy Cam, you will of course be eager to return later and review the images it has captured for you. There are several different ways this can be done. Reviewing Images on an External Video Monitor A TV monitor can also be used to play back pictures (or videos) from the device. Connect a TV monitor or a viewing device (such as a digital picture frame) that has a standard composite video input (RCA jack) to the Trophy Cam `s "TV Out" mini jack using the supplied cable. Then: · Put the power switch in SETUP mode (switch to OFF first). [. . . ] Make sure that you have been saving the changes to any parameter settings that you made while in Setup mode, by pressing "OK" after changing the setting. If you don't save your new setting after changing it, the camera will continue to use the original default setting for that parameter. 28 Technical Specifications Image Sensor Maximum Pixel Size Lens IR-Flash Range Display Screen Memory Card Internal RAM Picture Size Video Size PIR sensitivity Operation Response Time Triggering Interval Shooting Numbers Video Length Power Supply Stand-by Current Power Consumption User Interface Interface Security Operating Temperature Operating Humidity Security authentication 5 Megapixel Color CMOS 2560x1920 (5MP) F=3. 1; FOV=50°; Auto IR-Cut-Remove (at night) 36'-45' (12m-15m) B&W Display: 24x32mm(1. 5") SD or SDHC Card, Maximum capacity 4GB 32MB 5MP = 2560x1920; 3MP = 2048x1536 640x480/30fps, 320x240/30fps PIR with 3 sensitivity levels: High/Normal/Low Day/Night 1s 1sec. programmable 8xAA recommended, 4xAA as emergency power < 0. 3mA(<7mAh/day) 200mA (+530mA when IR-LED lighted) LCD display TV out (NTSC/PAL); USB; SD card holder; 6V DC external Strap; ¼-20 attachment -20 - 60°C (Storage temperature: -30 - 70°C) 5% - 90% FCC/CE/RoHs/WEEE 29 TWO-YEAR LIMITED WARRANTY Your Bushnell® product is warranted to be free of defects in materials and workmanship for two years after the date of purchase. [. . . ]