User manual CALIBER RMD801BT

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual CALIBER RMD801BT. We hope that this CALIBER RMD801BT user guide will be useful to you.

Lastmanuals help download the user guide CALIBER RMD801BT.


Mode d'emploi CALIBER RMD801BT
Download
Manual abstract: user guide CALIBER RMD801BT

Detailed instructions for use are in the User's Guide.

[. . . ] 18 RMD 8 0 1 BT SAFETY PRECAUTIONS MANUAL To avoid short in your vehicles electrical system, be sure to disconnect the battery cable before beginning installation. The unit is intended for vehicles with a 12-volt battery and negative grounding. Before installing the unit in a recreational vehicle, truck, or bus, check that the battery voltage is 12 volts. Remove the two transport screws from the top of the unit before installation. [. . . ] This unit is designed for use with four (4) speakers with impedance between 4 Ohms to 8 Ohms. An Impedance load of less than 4 Ohms could damage the unit. Never bridge or combine the speaker wire outputs. When not using four speakers, use electrical tape to tape the ends of the unused speaker outputs to prevent a short circuit. Never ground the negative speaker terminals to chassis ground. 7 RMD 8 0 1 BT BASIC OPERATION MANUAL 1. Turning the unit On / Off Press the Power Button to turn the unit on. When the unit is on, press the Power Button once to turn the TFT off. During TFT off, the video out signal will be available so that the connected monitor will show the screen of the unit. Press the Power Button again to turn the TFT back on. Press and hold the POW button again to turn the unit off. Mode Selection Press the MODE Button to cycle the Play Modes between RADIO, USB, SD and AUX in. Volume Use the VOL +/- Button to adjust the volume level. Turn the button clockwise to increase the volume, and vice versa. The larger the number of volume, the higher the volume level. You can also adjust the volume by sliding the volume icon on top of the screen. Bass Press the SEL Button until the display shows “BAS”. When EQ is ON, bass control is not available. Treble Press SEL Button until the display shows “TRE”. When EQ is ON, treble control is not available. Balance Press SEL Button until the display shows “BAL”, then use the VOL +/- Button to adjust the balance between the left & right speakers. Fader Press SEL Button until the display shows “FAD”, then use the VOL +/- Button to adjust the balance between the front & rear speakers. [. . . ] Press and hold the BND/NP/ SUB button to activate or deactivate this function. 14 MANUAL RMD 801BT MAINTENANCE Cleaning the Unit Do not use any liquids to clean this unit. Do not use petroleum distillates to clean this unit. Use a clean, dry cloth to clean this unit. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE CALIBER RMD801BT

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual CALIBER RMD801BT will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag