User manual CANON BJC-4000 BROCHURE

[. . . ] All of these print media are specially designed and manufactured to work with your Canon color printer so you can produce the finest output possible. Canon has an extensive dealer network equipped to offer you supplies as you need them. to find a dealer near you, call the Canon Referral Service at 1-800-848-4123. If supplies are not available from your local dealer, you can order directly from Canon by calling 1-800-671-1090 BJ Cartridge and BJ Tanks You can use the following BJ cartridges with the BJC-4000 printers: BC-21e Color BJ Cartridge BC-20 Black BJ Cartridge BC-22e Photo BJ Cartridge BC-29F Neon BJ Cartridge You can purchase the following BJ tanks for use in the BC-21e Color BJ Cartridge: BCI-21 Black BJ Tank BCI-21 Color BJ Tank BJ cartridges contain the Bubble Jet print head and BJ tank(s), while BJ tanks contain ink only. 4300 Chapter 1 Page 2 Canon has more engineers dedicated to creating quality ink for providing the best results for output on Bubble Jet printers than any other organization. [. . . ] (You can also manually feed envelopes one at a time. ) 1 Set the paper thickness lever. Make sure that the paper thickness lever is set to the right. 4300 Chapter 3 Page 14 2 Make sure the paper support is raised, and the paper output tray is extended. 3 Prepare the envelopes. Arrange the stack of envelopes on a firm surface and press down firmly on the edges to make the folds crisp. Press all the way around the envelopes to remove any curls and expel air from inside the envelopes. Make sure any curls are removed from the flap of each envelope. 4300 Chapter 3 Page 15 4 Insert the envelopes. Slide a stack of envelopes into the sheet feeder until it stops. Align the edge of the paper guide with the left edge of the stack of envelopes. 5 Start your print operation. Make sure the printer is on. 4300 Chapter 3 Page 16 Using Canon's Specialty Papers This section provides guidelines for printing on Canon's Specialty Papers and describes special procedures required for High Resolution Paper, Fabric Sheets, and Banner Paper. Specialty Paper Guidelines Be sure to read any instructions that come with your Canon Specialty Paper. These instructions provide important information regarding how to achieve the highest print quality with these papers. For transparency film, back print film, high gloss film, and glossy photo paper, follow these guidelines When automatically feeding transparencies or back print film, remove each sheet after it is delivered. Let the printed sheets of film or paper dry completely before storing them. Paper Type Canon Glossy Photo Paper GP-210 Canon Fabric Sheet FS-101 Canon CF-102 Transparencies Canon Back Print Film BF-102 Drying time 10 minutes 1 hour 15 minutes 15 minutes When a sheet of film has dried completely, cover its printed side with a sheet of plain (not coated) paper before storing it; this is recommended even if you place the sheets of film in a clear file or plastic holder. 4300 Chapter 3 Page 17 Do not leave the film in the sheet feeder for long periods of time. Dust and dirt may accumulate on the film resulting in spotty printing. To avoid smudging caused by finger prints, use a pair of thin cloth gloves while handling the film. To avoid fading, do not expose the printed film to prolonged sunlight. Store unused film at temperatures between 59ºF to 86ºF (15ºC to 30ºC). The relative humidity should be between 10% and 70%. Uncurling Back Print Film If Back Print Film becomes curled, follow these steps to uncurl it: 1 Cover the non-glossy side of the film with a sheet of plain paper. 2 Roll the film and paper up in the direction opposite the curl. Do not roll the film too tight. Start the print operation from your Windows application. 4300 Chapter 3 Page 23 4 Set up the BJC-4000 Printer Driver for Windows. Dry and then wash the fabric sheet. Let the printed fabric sheet set for about one hour to allow the ink to completely dry. When dry, peel the film backing from the printed fabric sheet. Do not remove the film backing before printing. Wash the printed fabric sheet for about three minutes under lukewarm running water to remove extra ink. Hang the fabric sheet up to dry it again. Iron the dried fabric sheet with a clothes iron. See the booklet that comes with Fabric Sheet FS-101 for details on drying and washing. Printing on Banner Paper For best results, use Canon Banner Paper. To set up a print job on banner paper, you must decide on the number of sheets you need. You can print banners from 2 to 6 sheets in length. Always leave an extra sheet at the end of the banner- just in case the type runs over. The shaded portions of the drawing below illustrate the maximum recommended printing area of banner paper. 4300 Chapter 3 Page 24 Printing on banner paper requires quite a bit of ink. If you think your BJ cartridge may run out of ink, use a new BJ cartridge. [. . . ] The printer is now ready for printing. If you are printing high density graphics when a paper jam occurs, feed at least two sheets of paper through the printer to clean the rollers. Technical Notes Compaq Presario 7170/7180 Problem A [k prints at the top of the page when printing from Windows 95 on a Compaq Presario 7170/7180 Cause Configuration of parallel port in CMOS Solution Change CMOS on Compaq Presario 7170/7180 to enable bi-directional capability Reboot computer, press "delete" to go into CMOS setup At setup menu, cursor to "Advanced System Setup" and "Enter" to select From Advanced System Setup menu, select "Integrated Peripherals" From the Integrated Peripherals Menu, Cursor to 'LPT Extended Mode" (Note: This is different than LPT1 mode) The LPT Extended Mode will probably show "Standard"- Use the "Page Down" key to cycle to "ECP Mode" Press "ESC" key to back to Advanced System Setup Menu Press "ESC" key to go back to main setup menu Press "F10" to save new configuration, and confirm save by answering "Yes" to final question 4300 Chapter 5 Page 5 Toshiba Laptop Problem A[K prints at the top of the page and/or partial printout when printing on a Toshiba laptop. Cause Configuration of parallel port in CMOS and LPT. VXD file. Case #1 Partial printout may occur with the following settings: CMOS value for LPT1 is ECP LPT. VXD v4. 00. 950 file size 35, 479 Case #2 [K is printed at top and the rest of the page is correct with the following settings: CMOS value for LPT1 is Standard Bi-Directional LPT. VXD v4. 00. 950 file size 35, 487. Solution This corrected configuration should provide correct output. [. . . ]