User manual CANON ES8000V BROCHURE

[. . . ] IF YOU DO NOT AGREE TO THE TERMS OF THIS AGREEMENT, DO NOT OPEN THE SEALED DISK PACKAGE AND PROMPTLY RETURN THE CANON SCANNER, THE DISK PACKAGE CONTAINING SCANNER DRIVER SOFTWARE PROGRAMS AND/OR SCANNER UTILITY SOFTWARE PROGRAM PROPRIETARY TO CANON OR ITS LICENSOR (THE “SOFTWARE”) AND THE ACCOMPANYING DOCUMENTATION AND OTHER ITEMS TO THE PLACE WHERE YOU OBTAINED THEM FOR A REFUND BEFORE THEY ARE USED OR OPENED OR UNPACKED. In consideration of the right to use the SOFTWARE, you agree to abide by the terms and conditions of this Agreement. GRANT OF LICENSE: Canon grants you the personal, nonexclusive right to use the SOFTWARE only on a single computer. You shall need to obtain multiple licenses separately from Canon when you shall install the SOFTWARE on multiple computers. [. . . ] For details, refer to the User Manual. Hint When opening the Document Feed Tray by hand, place your fingers in the indents at both sides of the tray, and open it gently. When power is switched OFF while the home position setting of the Document Feed Tray is high, the tray moves to the lowest position before the scanner turns OFF. CAUTION When the home position is set to high, make sure to turn the power OFF before closing the tray. Closing the Document Feed Tray while the scanner is ON may damage the scanner. 17 ■ Document Guides Unlock the document guides by gently pressing both sides of either guide (a), and sliding the document guides to match the width of your document (b). Adjusting the Document Guides The document guides normally extend at equal distances from the left and right of the center of feeding so that your documents are centered in the feed inlet. However, each document guide has its own lock lever, so you can load documents to the left or right of center by locking the document guides at the appropriate positions. Locking the Document Guides Hint The positions of the left and right document guides can also be locked independently for off-center loading. For details, see “Adjusting the Document Guides” (p. 18). ■ Document Feed Tray Extension Pull out the tray extension as needed for the length of your document. ■ Loading Documents at the Left Side This example shows the procedure for loading documents at the left side of the feeder. 1. Spread the document guides all the way to the left and right. 18 2. Load your documents against the left feed guide. 5. Slide the left document guide to the left edge of your documents. 2 Basic Operation 3. Lock the left document guide (a) by pulling out the lock lever, then slide the right document guide to the right edge of your documents (b). ■ Resetting the Document Guides To reset the guides so that they are equidistant from the center, perform the following procedure to spread the guides to the left and right as far as they will go. 1. Confirm that the right document guide is locked (a), and slide the left guide all the way to the left (b). 4. Lock the right document guide (a), and unlock the left document guide (b). 2. Scan Page Only one page of the document is scanned. Scan Job The scanning conditions and scan mode (Scan Batch to File, Scan Batch to Printer, or Scan Batch to Mail) are registered in advance as a job. The scan job can then be performed by selecting the registered job from the dropdown list (a) or by clicking (Scan Job) on the toolbar (b). 2 Basic Operation ■ Scanning with CapturePerfect The following three scanning methods are available from the CapturePerfect Scan menu. Scan Batch to Printer Prints scanned images on a specified printer Scan Batch to File Saves scanned images as files in a specified folder b Hint (Network) DR-X10C Scan Batch to Mail Starts your e-mail program and attaches the scanned image to a new e-mail message a The following two scan jobs are already registered and up to 99 additional jobs can be registered. • Color Document Scan the document using 24-bit color, simplex, at 300 dpi resolution, and save the file in the folder [My Pictures] under the folder [My Documents]. • Binary Document Scan the document in black-and-white, simplex, at 200 dpi resolution, and save the file in the folder [My Pictures] under the folder [My Documents]. 25 Scan To Presentation This mode is convenient when a compact scanner is used in an environment such as a conference hall, where it is connected to a large display or projector. By setting CapturePerfect for full-screen display before scanning, scanned images are displayed at full size on the screen. Hint This is not usually practical for large scanners such as the DRX10C. CapturePerfect 3. 0 starts. ■ Using CapturePerfect 3. 0 This section describes how to start CapturePerfect 3. 0 and scan documents. The procedure for using the Scan Batch to File function is described here as an example. For details, refer to the CapturePerfect 3. 0 Operation Guide. 2. From the [Scan] menu, select [Select Scanner]. 1. From the Windows task bar, click [Start] ➔ click [All Programs] ➔ [CapturePerfect 3. 0] ➔ [CapturePerfect 3. 0]. The [Select Scanner] dialog box opens. 3. Select [Canon DR-X10C] and click [Settings]. IMPORTANT If [Canon DR-X10C] is not displayed in the list of scanners, you must re-install the ISIS/TWAIN driver. 26 4. [. . . ] Grayscale 200 dpi Simplex 130 pages/min. 600 dpi (speed priority) Simplex 82 pages/min. 600 dpi (image quality priority) Simplex 32 pages/min. 600 dpi (speed priority) Simplex 46 pages/min. [. . . ]