User manual CANON FAXPHONE 1100 BROCHURE

[. . . ] DTMF signalling also provides faster call set up. This CE Marking shows compliance of this equipment with Directive 73/23/EEC and Directive 89/336/EEC (as amended by Directive 92/31/EEC), both as amended by Directive 93/68/EEC. L'estampille CE indique que ce matriel est conforme aux dispositions de la Directive 73/23/CEE et de la Directive 89/336/CEE (modifie par la Directive 92/31/CEE), toutes deux modifies par la Directive 93/68/CEE. Diese CE-Markierung weist darauf hin, da dieses Gert mit Richtlinie 73/23/EWG und der durch Richtlinie 92/31/EWG genderten Richtlinie 89/336/EWG bereinstimmt, die beide durch Richtlinie 93/68/EWG gendert wurden. Denne CE-mrkning indikerer, at dette udstyr flger Direktiv 73/23/EU og Direktiv 89/336/EU (som udvidet med Direktiv 92/31/EU), begge som udvidet med Direktiv 93/68/EU. [. . . ] If you want to use this feature, press SET. Use the buttons on the numeric keypad to enter the time in 24-hour format. You can set up to 5 times to relay documents within a 24-hour period every day. 10. RELAY B'CAST This feature switches relay broadcasting for this group on and off without altering any of the other settings. ON OFF Your fax unit receives and relay a document set for relay broadcasting. Your fax unit will not receive and relay a document set for relay broadcasting Changing the Relay Broadcast Settings Follow this procedure to change the relay broadcast settings. If you want to add to the list of fax units to receive relay broadcasts from your fax unit, make sure that the numbers you want to add are registered for One-touch or Coded Speed Dialling. If you want to set your fax unit to confirm the identity of the originator before it receives a document for relay broadcasting, make sure the telephone number of the originator's fax unit is registered for One-touch or Coded Speed Dialling on your fax unit. 1. (Q9-3) RELAY TX GROUP 1. SETUP FILE < 9-6 < 2. Press the search buttons until you see the display below. RELAY TX GROUP 2. CHANGE DATA SET 3. Press SET. CHANGE DATA SET RLY TX GROUP# 00 Using a Relay Network Chapter 9 ABC DEF 1 GHI JKL 2 M NO 3 6 WXYZ SET 4 PQRS TUV 5 8 0 4. Your fax can not confirm whether or not the other party's fax has been set up properly as a relay unit. If an ITU-T password is set on the other party's fax you must send the document with a password. Otherwise, the other fax will not receive your document. After the relay fax is set up to participate in a relay network, it should receive and relay documents automatically. By following the initial setup procedures in the previous section, the relay fax unit can be set to confirm the identity of the originator before sending and to send a relay transmission report to the originator after your fax unit requests the other unit to relay a document. When your fax unit is the originator of a relay transmission with this method, it does not check to ensure that the fax to receive and relay the transmission is set up properly for relay transmission. Even when the fax is not set up to relay your documents, your fax unit reports such a transmission as a successful relay transmission. Make sure the relay unit is set up correctly to relay documents that it receives from your fax unit. Sending a Document to a Relay Unit with Speed Dialling You can register a telephone number for relay sending under a One-touch or Coded Speed Dialling button. Check these points before you send a document to another party for relay: Contact the other party and ask for the ITU-T subaddress and password they are using for receiving documents to relay. The other party's fax unit does not have to be a Canon fax unit, but make sure the other party's fax unit supports the use of ITU-T subaddresses and passwords. Chapter 9 Using a Relay Network 9-9 Perform the procedure to register a telephone number for One-touch or Coded Speed Dialling. (Q4-6, 4-14) If the speed dialling buttons are already set up, perform the procedure to change the One-touch or Coded Speed Dialling settings. (Q4-6, 4-14) When you do the speed dialling settings, turn on the OPTIONAL SETTING feature and select TX TYPE. Select ORIG RELAY TX and then set the ITU-T subaddress and password. [. . . ] Please remember, however, that documents received in a confidential mailbox or a memory box can not be transferred. Transfer password Protects the transfer settings from unauthorized access. You must enter the transfer password, a four-digit code (0000-9999), in order to view or change the transfer settings. Transmission time A fax transmission consists of three stages: the pre-message handshake, the message transmission, and the post- message handshake. [. . . ]