User manual CANON IMAGECLASS D1120 BROCHURE

[. . . ] If the setup menu does not start up, run the setup. exe application on the CD-ROM. 1. Peel off the orange tape from all the places on the outer casing marked below. 2. Flip up the retard roller lock lever (1), and slide it to the right (2). The setup menu consists of the following screens: Menu Screen Typical Installation 2. Carefully open the document feed tray and protective sheet. Document Feed Tray 3. Load the retard roller so that its notch aligns with the shaft on the scanner. * Installs all of the software displayed. Read Manuals Custom Installation 3. Peel off the orange tape from all the places marked below. 4. Slide the lock lever to the left so that its shaft fits into the retard roller (1), and then flip the lock lever completely down to lock the retard roller (2). * The User Manual and CapturePerfect 3. 0 Operation Guide electronic manuals for the scanner are installed on the computer with the rest of the software. [. . . ] (☞STEP3) Read the software license agreement, and click [Yes] if you consent to its conditions. Installation of the scanner driver starts. DR-4010C Power Cord USB Cable Job Labels Installing the Software 2. Load the roller unit so that its notch aligns with the shaft pin on the scanner. Easy Start Guide (This Manual) Reference Guide DR-4010C Setup Disc Adobe Acrobat Setup Disc Install the software before connecting the scanner to the computer. Warning The Job Tool is installed after the scanner driver. ❏ Before installing the software, make sure your computer is correctly running one of the following versions of Windows. For details, refer to the Reference Guide. 0880281099-L5T1P7-BR01 CANON CANADA INC. 6390 DIXIE RD MISSISSAUGA ON L5T 9Z9 • Windows 2000 Professional SP4 or above Retard Roller Roller Unit Warranty Card Registration Card • Windows XP Home Edition SP2 or above 3. Slide the lock lever to the left (1), and then lift the roller unit into place (2). • Windows XP Professional SP2 or above • Windows XP Professional x64 Edition Note ● ● Items included in this package are subject to change without notice. Keep the package and packing materials for storing or transporting the scanner. ❏ Do not connect the scanner to the computer before installing the software. If you connect the scanner and turn it ON before you install the software, a wizard screen will appear. If this wizard appears, click [Cancel] to exit the wizard, and then turn the scanner OFF. 7. Click [Finish] to complete the installation. Next, the installation wizard for CapturePerfect 3. 0 appears. 4. For details on the feed selection lever, refer to the User Manual. Warning Type B Insert the plug with the mark facing down. ❏ When the scanner is connected by a SCSI cable, always turn ON the scanner before the computer. Turning ON the computer first may prevent it from recognizing the scanner properly. ❏ Be sure to log on with Administrator privileges when logging on to Windows. ❏ Wait at least 10 seconds before turning the scanner ON again after turning it OFF. ❏ If the scanner will not be used for an extended period, be sure to unplug it from the power outlet for safety. Feed Selection Lever 13. Click [Finish] to complete the installation of the User Manual. When Connecting by SCSI 1. Make sure your computer is turned OFF before connecting the SCSI cable. Make sure the scanner’s power switch is in the OFF position. If the power switch is in the ON position, press the switch to turn it OFF. Power Switch 5. Press job button 3. The “Monitor for DR-4010C” window appears at the bottom right of the computer screen, and scanning starts. 14. When all installations are complete, the installation completed screen appears. Click [Back] to return to the menu screen. OFF Position ON Position 1. [. . . ] Job button 1: Scan start Job button 2: Scan stop Job button 3: Scan The job button functions can be changed. For details, refer to “Scanning With the Job Function” in the User Manual. By default, scanned image files are saved in the “My Pictures” folder in “My Documents. ” By default, scanned image files are saved as PDF files with a 17-digit file name that indicates the date and time when the image was scanned. You can change the scan settings and save destination folder by using the “Job Registration Tool” located in the Programs menu of Windows. 5. Connect the scanner to your computer with the SCSI cable. [. . . ]