User manual CANON IMAGECLASS MF5850DN BROCHURE

[. . . ] 1-1 Installing with the Add-A-Plotter Wizard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6 Chapter 2 Printing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1 Printing Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1 Chapter 3 Setting Up a Print Job . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The Plotter Configuration Editor dialog box opens. 2-1 imagePROGRAF HDI Driver Guide Printing 5. Perform the settings that you need for the print job. Note For more details about how to perform the settings in the Plotter Configuration Editor dialog box, please refer to Chapter 3, "Setting Up a Print Job" (p. 3-1). 6. Click the OK button to close the Plotter Configuration Editor dialog box. The Plot dialog box opens. Note · The content of the settings done in the Plotter Configuration Editor dialog box are reflected in the Paper size and paper units settings on the Plot Settings sheet of the Plot dialog box. · For more details about the Plot dialog box, please refer to the AutoCAD manual. 7. Perform the settings that you need on the Plot Settings and Plot Device sheets, then click the OK button. The print job begins. Note · If the output exceeds the number of pixels prescribed for the media, in order to prevent AutoCAD from hanging up during the print job a warning dialog box opens and asks if you want to lower the resolution or reduce the number of colors. If this occurs, click the OK button to cancel the print job and then lower the resolution or reduce the number of colors. · Some media may not allow printing with certain resolution settings. If you have selected a resolution setting that cannot be used for printing, then a dialog box will open and prompt you to change the resolution. If this occurs, click the OK button to cancel the print job and then lower the resolution. Follow the procedure below to open the Custom Properties dialog box. In the Plotter Configuration Editor dialog box, select and open the Device and Document Settings sheet. Note For more details about how to open the Plotter Configuration Editor dialog box, please refer to Chapter 3, "Opening the Plotter Configuration Editor Dialog Box" (p. 3-1). 2. The Device and Document Settings sheet opens and switches to the display that presents the custom properties settings. 3. The Custom Properties dialog box opens. Custom Properties Dialog Box Functions This section describes how to perform the settings in the Custom Properties dialog box. 3-5 imagePROGRAF HDI Driver Guide Setting Up a Print Job Selecting the Media Type and Ink Type Use these settings to set the media and ink type. Select the media type from the Media Type list under Media and Ink Settings. Note · Here is a list of the types of media that can be selected. Plain Paper, Fine Art, Coated Paper, Glossy Photo Paper, Synthetic Paper, and others · The type of media that you can use for printing depends on the type of black ink in use. · For the Media Type you must select the setting for the media actually loaded in the printer. If the Media Type selection is not the same as the media actually loaded in the printer, the print results will not be correct. · Click the Media Detailed Settings button to open the Media Detailed Settings dialog box. In this box you can perform the settings for the ink drying time and other items. For more details, please refer to "Media Detailed Settings" (p. 3-7). 2. [. . . ] Media Thickness presents the following items for selection. Media Thickness Printer Default Thick Standard Thin 2. Vacuum Strength Select a setting for the amount of suction applied to the media. Select a setting from the Vacuum Strength list in the Vacuum Strength dialog box. [. . . ]