User manual CANON IMAGEFORMULA CR-180

[. . . ] CANON CHECK READER INSTRUCTIONS CANON ELECTRONICS INC. 1248, SHIMOKAGEMORI, CHICHIBU-SHI, SAITAMA 369-1892, JAPAN CANON U. S. A. 6390 DIXIE ROAD, MISSISSAUGA, ONTARIO L5T 1P7, CANADA CANON EUROPA N. V. BOVENKERKERWEG 59-61, P. O. BOX 2262, 1180 EG AMSTELVEEN, THE NETHERLANDS CANON LATIN AMERICA, INC. [. . . ] Connect the plug securely into the power source. ■ Use only the power cord and plug provided with the scanner. ■ Before you connect the power cord, be sure to turn OFF the power switch. ■ Be sure to connect the scanner to an AC 220-240V (50/60 Hz) or AC 120V (60 Hz) power supply, according to your region’s requirements. ■ Do not plug the scanner into an outlet shared with another device. If you use an extension cable, pay attention to the total amperage of the cable. 25 Chapter 2 Preparation Before Use Turning ON and OFF the Power Follow the procedures below to turn the scanner power ON and OFF. Turning ON the Power Be sure to turn the power of all connected SCSI devices ON before you turn the computer ON. Important 1 To turn ON the scanner, press the power switch. Jog Start Stop ON Important ● The LED above the Start button, flashes after you turn the power ON for a few seconds, then it remains lit. ● The eject pocket document sensor may make an incorrect detection when scanning starts if a bright outside light or fluorescent light is shining on the scanner’s eject pocket when the scanner is turned on. If this happens, pull the flapper on the eject pocket all the way forward and then return it to cancel the incorrect full detection and then try scanning again. 44) ● If the scanner does not work, or the LED continues to flash, there is a problem with the scanner. Turn OFF the power, and contact your local retailer or a Canon service department. WARNING If you hear strange sounds, detect smoke or abnormal heat, sense a vibration, or smell odd odors around the scanner, turn OFF the power immediately and disconnect the power cord from the power outlet. Failure to do so, may cause a fire. 2 Turn ON your computer. 26 2. 5 Turning ON and OFF the Power 3 Windows recognizes the CR-180 as new hardware, and installation starts automatically. (Windows 2000) 2 (Windows XP) ● The installation finished message is not displayed in Windows 2000. ● If your operating system is Windows XP, a message appears after the device driver is installed. Note ● The CR-180 will be registered as “CANON CR-180 SCSI” or “CANON CR-180 USB” in the Imaging Device directory. The displayed device name of the CR-180 differs depending on the connection, via SCSI or USB. Turn OFF the power to the scanner and the computer before changing the connections, and then turn ON the power, and let the computer recognize the scanner again. 27 Chapter 2 Preparation Before Use Turning OFF the Power Turn OFF the power to the computer if you are using a SCSI cable to connect the scanner. Important 1 Turn OFF your computer. 2 To turn OFF the scanner, press the power switch. OFF CAUTION ■ Wait at least 10 seconds before turning the scanner back ON. ■ For your safety, disconnect the power plug from the power outlet if you are not using the scanner for a long period of time. 28 2. 6 Preparing the Ink Cartridge Preparing the Ink Cartridge This section describes how to prepare the ink cartridge so that you can use the imprinter to print text on scanned documents. About the Ink Cartridge The ink cartridge is not included with the scanner. Purchase an ink cartridge separately, as shown below. Compatible ink cartridges: Hewlett Packard ink cartridge, model numbers C6602B (blue), C6602G (green), C6602R (red) For details on installing the ink cartridge, see “Replacing the Ink Cartridge, ” on p. 63. Note 2 Adjusting the Print Position You can adjust the print position to three different levels. 1 Remove the top cover. 2 Press the open button, and pull the maintenance cover open to the right and left. 29 Chapter 2 Preparation Before Use 3 Squeeze the print position adjustment lever and lift up to adjust the print position. ● Adjust the position of the text so that it aligns with the adjustment line on the print position adjustment lever. ● The value of the adjustment line indicates the distance from the bottom edge of the document to the center of the text. Note Adjustment Line Top: 1. 6" (40 mm) from the bottom edge of the document Middle: 1. 4" (36 mm) from the bottom edge of the document Bottom: 1. 3" (32 mm) from the bottom edge of the document 4 Close the maintenance cover in the order shown in the diagram below. 5 Carefully replace the top cover. If the top cover is not firmly in place, the ink cartridge is not installed properly. Check the ink cartridge. 30 Note Chapter 3 Software This chapter describes how to install and use the scanning software, Scanning Utility, and ISIS/TWAIN driver. 3. 1 How to Use the Software . . . . . . . . . . . . . . . . . . . 32 Starting and Closing the Scanning Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 How to Use the ISIS/TWAIN Driver . . . . . . . . . 34 3. 2 Uninstalling the Software . . . . . . . . . . . . . . . . . [. . . ] It is an open system in which business proprietors can participate voluntarily. The targeted products are office equipment, such as computers, monitors, printers, fax, machine, copiers, and scanners. The standards and logos are uniform among participating nations. FCC REGULATIONS (For 120V models) This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. [. . . ]