User manual CANON IMAGEPROGRAF IPF825 MFP M40 CANON_PROFESSIONAL_PRODUCT_GUIDE_NEW.PDF

[. . . ] 1 Transfer Specification Item Synchronous System Transmission Speed Data Length Parity Stop Bit Flow Control Asynchronous 9600 / 19200 8 bit N/A 1 N/A Specification Note1) Transmission Speed: initial setting value is 19200 Note2) Transmission Speed can be changed in service mode. 2 Connection Dedicated serial cable must be used for a connection to a computer and a projector. pC COM 1 Projector Control Port (D-Sub 9 Pin) (D-Sub 9 Pin) -2- LV-7292A/LV-7297A/LV-7392A/LV-7393A/LV-7398A/IMAGEPROGRAF IPF825 MFP M40/LV-7292M/LV-7297M/LV-8227M Expand Serial Command Functional Specifications ３．Notes for communication 1. Expand Serial Command is defined as one command / one line that starts with “C” and ends with carriage return (0x0D) 2. [. . . ] Note2) When there is no signal detected, projector returns 101 and the command does not execute. 8 CF_KEYSTONE Command Command “CF_KEYSTONE_%1”[CR] “UP” ------------- Correct Keystone distortion to reduce upper part of image “FUP” ----------- Correct Keystone distortion to reduce upper part by 2steps “DN” ------------- Correct Keystone distortion to reduce lower part of image “FDN” ----------- Correct Keystone distortion to reduce lower part by 2steps “RST” ------------ Reset Keystone Change Keystone distortion correction This command is available in normal Power ON status. Acceptable Response “000”[CR] “Error Code”[CR] “201”[CR] ----When reaching the Keystone correction limit or reaching 1 step to correction limit and “FDN”/”FUP” is received. (The command is not executed) %1 Details Unacceptable 8. The value set by this command is stored in EEPROM and its setting is effective even after ALL is OFF This command is available in normal Power ON status. The status set by this command is stored in EEPROM and its setting is effective after ALL is OFF This command is available in normal Power ON status. 8 Lamp Command CF_LAMPH Command Command %1 Details Response “CF_LAMPH_%1”[CR] “RST” Reset total lamp running time This command is available in normal Power ON status. 2 CF_LAMPMODE Command Command “CF_LAMPMODE_%1”[CR] “HIGH” ------------ Set lamp to High mode status “NORMAL” ------- Set lamp to Normal mode status “ECO” ------------- Set lamp to 3L mode status “UP” --------------- The same operation as pressing Up key or Left key “DN” --------------- The same operation as pressing Down key or Right key Select Lamp Mode The value set by this command is stored in EEPROM and its setting is effective even after ALL is OFF. When setting Volume value, the Sound Mute ON status is canceled just like RC operation. The value set by this command is stored in Projector. The value set by this command is stored in Projector. 12 CF_P-MANE Command Command “CF_P−MANE_%1”[CR] “OFF” --------------------------------- Set Power Management to OFF “READY” ----------------------------- Set Power Management to Ready “SHUTDOWN” --------------------- Set Power Management to Shut Down mode “UP” ----------------------- The same operation as pressing Up key or Left key “DN” ----------------------- The same operation as pressing Down key or Right key Set/Cancel Power Management The status set by this command is stored in EEPROM and its setting is effective after ALL is OFF This command is available in normal Power ON status. 13 CF_P-MANETIME Command Command ％１ “CF_P-MANETIME_%1”[CR] “01” ~ ”30” ----------------------- Directly select setting time by the minute “UP” ------------------------------- Plus one minute (01 → 02 → ･･･ → 30 → 01) “DN” ------------------------------- Minus one minute(30 → 29 → ･･･ → 01 → 30) Set Power Management time The status set by this command is stored in EEPROM and its setting is effective after ALL is OFF This command is available in normal Power ON status. 14 CF_ON-STA Command Command “CF_ON−STA_%1”[CR] “ON” -------------------------- Set Direct on active “OFF” ------------------------- Set Direct on inactive “UP” ----------------------- The same operation as pressing Up key or Left key “DN” ----------------------- The same operation as pressing Down key or Right key Set/Cancel Direct On Start The status set by this command is stored in EEPROM and its setting is effective after ALL is OFF This command is available in normal Power ON status. The status set by this command is stored in EEPROM and its setting is effective after ALL is OFF This command is available in normal Power ON status. The status set by this command is stored in EEPROM and its setting is effective after ALL is OFF This command is available in normal Power ON status. The status set with this command is stored in EEPROM and its setting is effective even after ALL is OFF. this command is available in normal Power ON status. Closed caption is available under conditions below; Entered signal is appropriate (Video, NTSC signal of S-video) and System is fixed to NTSC i. The status set with this command is stored in EEPROM and its setting is effective even after ALL is OFF. this command is available in normal Power ON status. Closed caption is available under conditions below; Entered signal is appropriate (Video, NTSC signal of S-video) and System is fixed to NTSC. [. . . ] 28 CR_FILREPL Command Command Details “CR_FILREPL”[CR] Get the information of Filter replacement time Acceptable Response %1 Unacceptable “000_%1”[CR] “1Y” ------------------- Over filter replacement time “1N” ------------------ Within filter replacement time “Error Code”[CR] -63- LV-7292A/LV-7297A/LV-7392A/LV-7393A/LV-7398A/IMAGEPROGRAF IPF825 MFP M40/LV-7292M/LV-7297M/LV-8227M Expand Serial Command Functional Specifications 9. 29 CR_FILTIMER Command “CR_FILTIMER” [CR] Get setting time which filter warning OSD is displayed Acceptable “000_%1”[CR] “2000” ----------------- 2000 hours “3000” ----------------- 3000 hours “4000” ----------------- 4000 hours “OFF” ---------------- No OSD display “Error Code”[CR] Command Details Response %1 Unacceptable -64- LV-7292A/LV-7297A/LV-7392A/LV-7393A/LV-7398A/IMAGEPROGRAF IPF825 MFP M40/LV-7292M/LV-7297M/LV-8227M Expand Serial Command Functional Specifications 9. This command affects the same as ”CR0” of Basic Serial command, but this has an error code. Acceptable “000_%1”[CR] “00”= Power ON “80”= Stand by “40”= Count down “20”= Cooling down “10”= Power failure “28”= Cooling down due to abnormal temperature “88”= Stand by after Cooling down “24”= Power saving cooling down “04”= Power saving “21”= Cooling down due to Lamp failure “81”= Stand by after Cooling down due to Lamp failure “Error Code”[CR] Response %1 Unacceptable 9. [. . . ]