User manual CANON IMAGERUNNER 7105 CANON GREEN TIPS FLYER

[. . . ] If Adobe Reader/Acrobat Reader/Acrobat is not installed on your system, please download it from the Adobe Systems Incorporated website (http://www. adobe. com). How This Manual Is Organized Chapter 1 Chapter 2 Chapter 3 Chapter 4 Chapter 5 Chapter 6 Installation Printing Scanning PC Faxing (MF5750/MF5770 Models Only) Troubleshooting Appendix Considerable effort has been made to ensure that this manual is free of inaccuracies and omissions. However, as we are constantly improving our products, if you need an exact specification, please contact Canon. Contents Preface . xi Chapter 1 Installation System Requirements . . 1-3 Installing Software on Your Computer. [. . . ] (Rulers) Shows the ruler at the upper and left edges of the preview to make accurate measurements. (Information) Lists the scanning information. To Detach and Move the Toolbar To detach the Toolbar from the [ScanGear MF] dialog box, click and hold on the edge of the Toolbar, then drag the Toolbar. It will return to its original position if you double-click on the title of the Toolbar. The Toolbar will adhere to a position if you drag it to the left or right of the preview area or the bottom frame. 3-24 Setting Preferences and Scanning with ScanGear MF Advanced Mode - Specifying the Parameters of a Scan You can specify the parameters of a scan by selecting a part of the image. When you scan again, only the part of the image you have specified is scanned. You can specify the parameters of a scan with one of the following methods. To Select the Parameters of a Scan Automatically After previewing, on the Toolbar, click . Clicking this button allows you to gradually crop off the image outside the borders detected in the preview image. To Specify the Parameters of a Scan 2 Do one of the following. Specify by dragging Click . Then click and drag from the upper left corner of the parameter you wish to specify to the lower right of the parameter. To adjust even further, drag the corner or border of the selected parameters. Specify size In (Width) and (Height), enter the parameters you want. NOTE If you clicked in step 1, entering either decides the other parameter. (Width) or (Height) automatically 3 4 To move the crop border you have selected, place the mouse pointer inside the crop border, then drag. To preview the image, click [Preview]. To delete the settings, click on an area outside of the crop border. Setting Preferences and Scanning with ScanGear MF 3-25 Scanning 1 3 To maintain the current width and height proportions set for the image even after selecting the parameters of the scan, click in the [Input Settings]. Advanced Mode Settings 3 Scanning Input Settings [Select Image Source] Selects where the document is placed ([Platen Glass] or [Document Feeder]). [Paper Size] Selects the size of the document to be scanned. The preview area size (height-to-width ratio) will change to the paper size you selected. Change this setting to set up the machine not to scan beyond the parameters of the scan when previewing or if you are scanning without specifying the parameters of the scan. Specify by entering a value in either (Width), (Height) or [%] (Scale), or click a [%] (Scale) value. After adjusting the settings, either click on another area or press the Enter key, and the other values linked to the input values will change. Even if you change these settings, the size of the cropping frame and the setting for [Output Resolution] will not change. The resolution when you actually scan will change in accordance with the value entered in [%] (Scale). The ratio of (Width) and (Height) is linked to (Width) and (Height) in Input Size. You can make settings for [%] (Scale) between 25 and 3200 in increments of 1%. [%] (Scale) is fixed to 100% if 4800, 7200 or 9600 dpi is entered in [Output Resolution]. Click to switch the orientation of the output size (landscape or portrait). This button is disabled when you select [Flexible] for [Output Size]. 3 Scanning [Data Size] Shows the data size of the scanned image according to your settings. Image Settings [Auto Tone] Set to [ON] to automatically adjust the tone of the image. The results of tone adjustment are reflected in the whole image and when the image is actually scanned. You cannot apply this setting if the preview image is not displayed. [. . . ] Resolution values are represented by horizontal data and vertical data, for example, 600 × 600 dpi. S Scalable fonts Scalable fonts allow characters to be printed in various sizes and rotation angles. This is different from bitmap fonts, which are printed in fixed sizes and angles. Glossary Scaling Enlarging or reducing the printed image. Scanner driver A program that controls how the computer and scanner interact. The scanner driver is provided with two drivers: The TWAIN and the WIA driver (for use with Windows XP). Separator page Optional pages printed at the beginning of each document to help separate one print job from another. Server A network computer that is directly attached to the printer. The server controls the printer and handles print jobs sent from the clients. [. . . ]