User manual CANON IR PASS 60PS BROCHURE

[. . . ] Please note that this warranty does not apply to repairs arising out of the malfunction of non-genuine Canon accessories, although you may request such repairs on a chargeable basis. Camera Body Temperature If your camera is used for prolonged periods, the camera body may become warm. Please be aware of this and take care when operating the camera for an extended period. About the LCD Monitor The LCD monitor is produced with extremely high-precision manufacturing techniques. More than 99. 99% of the pixels operate to specification. Less than 0. 01% of the pixels may occasionally misfire or appear as red or black dots. [. . . ] This is convenient for focusing on a specific part of a subject with greater certainty. symbol represents the AF frames as they appear in the LCD monitor. Shooting 1 Slide the mode switch to (Shooting) and select , from the FUNC. menu. or See Selecting a Shooting Mode (p. 53). 2 In the (Rec. ) menu, select . See Selecting Menus and Settings (p. 45). 3 4 Use the or [On] or [Off]. button to select You can shoot right after selecting an option. Press the MENU button. The display will return to the Shooting screen. The center AF frame mode is used when the digital zoom is activated. 73 Switching between Light Metering Modes You can switch between metering modes to shoot. Appropriate for standard shooting conditions, including backlit scenes. The camera divides images into several zones for light metering. It evaluates complex lighting conditions, such as the position of the subject, the brightness, the direct light, and the backlighting, and adjusts the settings to the correct exposure for the main subject. Averages the light metered from the entire frame, but gives greater weight to the subject matter at the center. Meters the area within the spot AE point at the center of the LCD monitor. Use this setting when you want to set the exposure on the subject in the center of the monitor. Evaluative CenterWeighted Average Spot 1 2 Slide the mode switch to (Shooting) and select or the FUNC. Select from See Selecting a Shooting Mode (p. · You can shoot right after selecting a value. The menu displays again after the shot, allowing you to change the settings easily. 3 Press the SET/FUNC. button. The display will return to the Shooting screen. 77 The nature of CCD image sensors is such that noise in the recorded image increases at long shutter speeds. This camera, however, applies special processing to images shot at shutter speeds slower than 1. 3 seconds to eliminate the noise, thereby producing high-quality images. Nevertheless, a certain amount of processing time may be required before the next image can be shot. · Please note that camera shake becomes a factor at low shutter speeds. If the camera shake warning appears on the LCD monitor, secure the camera to a tripod before shooting. · Use of the flash may result in an over-exposed image. If that occurs, shoot with the flash set to . Available Shutter Speeds The following shutter speeds (in seconds) are available. 1 1. 3 1. 6 2 2. 5 3. 2 4 5 6 8 10 13 15 78 Adjusting the Tone (White Balance) When the white balance mode is set to match the light source, the camera reproduces colors more accurately. Auto Daylight Cloudy Tungsten Fluorescent Fluorescent H The camera sets the white balance automatically according to shooting conditions. For recording under overcast, shady or twilight skies. [. . . ] 43 Quick Shot . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Shutter Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38, 74 Stitch Assist. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 160 MEMO 161 MEMO 162 MEMO 163 MEMO 164 MEMO 165 MEMO 166 MEMO 167 MEMO 168 MEMO 169 MEMO 170 MEMO 171 MEMO 172 MEMO 173 Disclaimer · While every effort has been made to ensure that the information contained in this guide is accurate and complete, no liability can be accepted for any errors or omissions. [. . . ]