User manual CANON PIXMA MX922 MX920 SERIES USER MANUAL (WINDOWS 8/8 X64/7/7 X64/VISTA/VISTA64/XP)

[. . . ] Wait until the POWER lamp displays a steady light. POWER button POWER lamp Load a few sheets of blank paper into the auto sheet feeder, align the paper with the right side of the cover guide, then slide the paper guide toward the left edge of the paper. Auto sheet feeder Print side NOTE: Do not touch the print head nozzles and the electrical contacts. Electrical contacts Ink port 3 Insert the yellow ink tank into the right-hand Print head nozzles Electrical contacts slot. Press the mark on the ink tank until it clicks into place and then its lamp lights red. Paper guide Cover guide PIXMA iP6600D Print Head 3 Firmly raise the print head lock lever until it stops into place. NOTE: Do not connect the USB cable at this stage. 3 When the screen shown on the LCD appears, click Ink tank lamp 3 Ensure that the message requesting head 4 Insert the remaining five ink tanks into their use the buttons to select a language and then press the OK button. Power Cord appropriate slots. Ensure that ink tank lamps light red. Refer to the color guide on the print head lock lever. alignment is displayed on the LCD, select Yes using the buttons and then press the OK button. And the print head is aligned automatically. IMPORTANT: It takes about 3 minutes and 30 seconds to finish printing. NOTE: If you leave the printer more than five minutes without using any button on the operation panel, the LCD goes into sleep mode automatically. [. . . ] And the print head is aligned automatically. IMPORTANT: It takes about 3 minutes and 30 seconds to finish printing. NOTE: If you leave the printer more than five minutes without using any button on the operation panel, the LCD goes into sleep mode automatically. Press the OK button to turn on the LCD again. 4 Pull down the paper output tray. Raise the 4 Slide the print head into the holder. The print head will rest at a slight angle. Lower the inner cover. NOTE: Put your fingers in the notches in either side of the paper output tray and pull down to open it. CLI-8C Cyan CLI-8PC Photo Cyan Cover 5 Close the inner cover and then the cover. The message requesting head alignment is displayed on the LCD. Go to the next step. NOTE: · The printer will perform a print head cleaning. Wait until the POWER lamp displays a steady light before proceeding. · If the Alarm lamp still lights even after the printer has stopped making operating noises, an ink tank may not be installed properly. Open the cover and make sure that the ink tanks are installed in the correct order directed on the label. When automatic print head alignment cannot be executed correctly, the message "Auto head align has failed. <See manual>" is displayed on the LCD. The system is restarted automatically. 9 Follow the on-screen instructions to install 3 Insert the Setup Software & User's Guide CD- NOTE: · If the CD-ROM folder does not open automatically, double-click the on the desktop. · Log on as an Administrator before continuing. 4 Double-click the Setup icon. NOTE: If you point to an application in the list, the explanation for the printer driver or an application is displayed. 8 Read the License Agreement, then click Yes. ROM. The setup program should run automatically. 4 When the main menu appears, click Easy the remaining software. When the Installation Results screen appears, click Next. Installation of the printer driver, on-screen manuals and applications will begin. Follow the instructions displayed on-screen. 9 Follow the on-screen instructions to register Tab your product. Install and follow the on-screen instructions. 10 When the Installation completed successfully screen appears, click Restart. A5 or larger (nonstandard-size paper: 203 mm/8 inches or more in length) 10 Follow the on-screen instructions to register 5 When the Authenticate screen appears, enter your product. NOTE: ·Select Easy Install in order to install the application software, electronic manuals and printer driver. Select Custom Install in order to choose the options you would like to install. ·To install PhotoRecord, click Custom Install and follow the instruction on the screen. 5 When the list of applications to install When the Installation completed successfully screen appears, click Exit. your administrator name and password. If you do not know your administrator name or password, click , then follow the onscreen instructions. appears, verify the contents, click Install, then follow the instructions on the screen. Move the cursor over items to display explanations of each application below. After restarting the computer, select Applications from the Go menu. [. . . ] If you do not know your administrator name or password, click , then follow the onscreen instructions. appears, verify the contents, click Install, then follow the instructions on the screen. Move the cursor over items to display explanations of each application below. After restarting the computer, select Applications from the Go menu. Double-click the Utilities folder, and then double-click the Printer Setup Utility (Print Center when you use Mac OS X v. 10. 2. x) icon. Check that your printer name is displayed on the Printer List. [. . . ]