User manual CANON REALIS WUX4000 PRO AV BROCHURE

[. . . ] 2 Communication System (Serial) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Communication System (LAN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] There are no GET commands available for this command. Example Control > FSTEPDRV=NEAR < I:OK * Commands are indicated by ">", and responses are indicated by "<". . 1-step control is exercised over the focus toward the NEAR end. Revision History / Date Changes Revised by Approved by - 33 - Projector SX80 MarkII User Commands GAMMA Gamma adjustment Format GAMMA=<Gamma adjustment:Number> GET□GAMMA / ?△GAMMA Setting values for <Gamma adjustment: Number> are -10 to 10. Environment OFF X Power ON PM O X D-RGB A-RGB1 A-RGB2 COMP Input VIDEO S-VIDEO HDMI USB None Response "i:OK" is returned if the parameter was set properly. For 'GET GAMMA' or '?GAMMA', current gamma adjustment is returned as 'g:GAMMA=<Gamma adjustment:Number>' For details on other responses, refer to the "Error List". Description (1) (2) (3) (4) (5) This performs the Gamma adjustment. This command functions in the same way as when "Image adjustment" - "Gamma adjustment" are selected on the menu. If numerical parameters are outside the range, "e:0801 INVALID_VALUE" is returned. This sets the currently selected input signal and image mode. The current gamma adjustment can be acquired using the applicable GET command. ("GET GAMMA") Example Setting > GAMMA=-1 < i:OK This sets the gamma correction to –1. Reference > GET GAMMA or ?GAMMA < g:GAMMA=3 * Commands are indicated by ">", and responses are indicated by "<". This retrieves the gamma adjustment. Revision History / Date Changes Revised by Approved by - 34 - Projector SX80 MarkII User Commands GUIDE Guide setting Format GUIDE=<Guide setting parameter:ID> GET□GUIDE / ?△GUIDE <Guide setting parameter: ID> ON Guide display ON OFF Guide display OFF Environment OFF X Power ON PM O X D-RGB A-RGB1 A-RGB2 COMP Input VIDEO S-VIDEO HDMI USB None Response "i:OK" is returned if the parameter was set properly. For 'GET GUIDE' or '?GUIDE', current guide setting is returned as 'g:GUIDE=<Guide setting parameter:ID>' For details on other responses, refer to the "Error List". Description (1) (2) (3) (4) This command is used to set the guide function display to ON or OFF. This command functions in the same way as when "System setting" - "Guide" are selected on the menu. The guide is cleared immediately when "GUIDE=OFF" is received while the guide is displayed. The current guide setting can be obtained using the GET command. ("GET HUE") Example Setting >HUE=8 <i:OK This sets the hue to +8. Reference >GET HUE or ?HUE <g:HUE=1 * Commands are indicated by ">", and responses are indicated by "<". This retrieves the hue. Revision History / Date Changes Revised by Approved by - 38 - Projector SX80 MarkII User Commands IMAGE Image mode setting Format IMAGE=<Image mode setting parameter:ID> GET□IMAGE / ?△IMAGE <Image mode setting parameter:ID> STANDARD Standard PRESENTATION Presentation SRGB sRGB MOVIE Movie PHOTO Environmental light compatible sRGB DCM_SIM DICOM monochrome * * "e:000A INVALID_PARAMETER" is returned if the model is not DICOM compatible Environment OFF X Power ON PM O X D-RGB A-RGB1 A-RGB2 COMP Input VIDEO S-VIDEO HDMI USB None Response "i:OK" is returned if the parameter was set properly. For 'GET IMAGE' or '?IMAGE', current image mode is returned as 'g:IMAGE=<Image mode setting parameter:ID>' For details on other responses, refer to the "Error List". Description (1) (2) (3) (4) This sets the image quality. This command functions in the same way as when "Image adjustment" - "Image mode setting" are selected on the menu. The final settings for the image mode are retained even when the power is turned off. Changing the setting may modify the following setting values. Setting Commands related to the settings Brightness Contrast Sharpness Gamma adjustment Dynamic gamma Progressive Saturation/Hue Memory color adjustment RGB gain/offset adjustment Lamp mode 6-axis adjustment 6-axis color correction (5) BRI CONT SHARP GAMMA DGAMMA PROG SAT/ HUE MEMCADJ RGBGAIN/RGBOFFSET LAMP 6AXADJ 6AXR～Y The current image quality can be acquired using the applicable GET command. ("GET IMAGE") Revision History / Date Changes Revised by Approved by - 39 - Projector SX80 MarkII User Commands Example Setting > IMAGE=PRESENTATION < i:OK This sets the image mode to "Presentation". Reference > GET IMAGE or ?IMAGE < g:IMAGE=CINEMA * Commands are indicated by ">", and responses are indicated by "<". This references the current image mode. Revision History / Date Changes Revised by Approved by - 40 - Projector SX80 MarkII User Commands IMAGEFLIP Flip display Format IMAGEFLIP=<Image flip setting parameters:ID> GET□IMAGEFLIP / ?△IMAGEFLIP <Image flip setting parameters:ID> NONE None CEILING Ceiling, Flip horizontally REAR Rear, Flip vertically REAR_CEILING Rear ceiling, Flip horizontally and vertically Environment OFF X Power ON PM O X D-RGB A-RGB1 A-RGB2 COMP Input VIDEO S-VIDEO HDMI USB None Response "i:OK" is returned if the parameter was set properly. For 'GET IMAGEFLIP' or '?IMAGEFLIP', current flip display setting is returned as 'g:IMAGEFLIP=<Image flip setting parameters:ID>' For details on other responses, refer to the "Error List". Description (1) (2) (3) (4) This command is used to flip the screen display in various ways (vertically or horizontally). This command functions in the same way as when "Display setting" - "Flip display" are selected on the menu. When the display is flipped, the "keystone distortion" settings are initialized (set to VKS:0). The current flip display status can be acquired using the applicable GET command. ("GET IMAGEFLIP") Example Setting > IMAGEFLIP=REAR < i:OK This displays the image backwards (flip vertically) on the screen. Reference > GET IMAGEFLIP or ?IMAGEFLIP < g:IMAGEFLIP=REAR_CEILING * Commands are indicated by ">", and responses are indicated by "<". This retrieves the flip display state. Revision History / Date Changes Revised by Approved by - 41 - Projector SX80 MarkII User Commands INPUT Input selection Format INPUT=<Input selection parameters:ID> GET□INPUT / ?△INPUT <Input selection parameters:ID> D-RGB D-RGB A-RGB1 A-RGB1 A-RGB2 A-RGB2 COMP Component VIDEO Video S-VIDEO S-Video HDMI HDMI USB USB Extension Environment OFF X Power ON PM O X D-RGB A-RGB1 A-RGB2 COMP Input VIDEO S-VIDEO HDMI USB None Response "i:OK" is returned if the parameter was set properly. [. . . ] Cannot execute command in current menu mode. Eliminate the cause of the error, and resend the command. Resend the command after canceling the freeze operation. Resend the command after exiting the current menu mode. [. . . ]