User manual CARDO SCALA RIDER TEAMSET

[. . . ] User Guide SCALA RIDER® TeamSetTM | Gebrauchsanleitung TM Guide d'Utilisation Guida di Avvio Guia de Usario English 1 | SCALA RIDER® TeamSetTM 2 SCALA RIDER® TeamSetTM | INTRODUCTION Congratulations, and thank you for choosing the SCALA RIDER TeamSet Bluetooth® Headset package for Motorcycle helmets. The retail box of the SCALA RIDER TeamSet contains two headset units: one headset for the driver and a second headset for the passenger: The Driver's unit includes a Bluetooth module that allows the following uses: 1. Bluetooth headset for mobile phone communication*, supporting Headset* and Handsfree* profiles (10m / 33 ft. Transmitting GPS navigation instructions from a Bluetooth enabled GPS device 3. [. . . ] Peel the foil cover from the Glue Plates' adhesive pad. Place the Glue Plate into position according to #3. Press firmly 15 seconds on all 3 parts of the Glue Plate. The adhesive pad bonds to full strength over the next 24 hours. Therefore it is recommended to not use the headset during this 24 hour period. Fasten the Clamp to the Glue Plate using the Allen screws that were previously removed. SCALA RIDER® TeamSetTM | POSITIONING THE SPEAKERS Attach the speakers to the Velcro inside your helmet opposite your ears (short speaker cord for the left ear [A] and the long speaker cord [B] for the right ear). You may want to use the supplied Velcro pad. Using two speakers inside the helmet may be prohibited in certain jurisdictions. If this is the case, you should tuck away the long corded speaker underneath the helmet padding as follows: Lead the speaker cord [B] alongside the rim of the padding to the right side and then back to the left side, near speaker [A]. Then place the speaker [B] underneath the padding. Speaker A Speaker B Cable Speaker A B Speaker REMOVING: Your headset can be removed for charging and storage by pressing your finger gently against the tab and sliding the headset up with the other hand. We recommend that you remove the headset from the helmet when not in use. Press here to remove English AUDIO SOURCES AND PRIORITIES The different Audio Sources that are connected to the SCALA RIDER TeamSet are prioritized as follows: 1. Mobile phone audio (Incoming/outgoing calls) / GPS Highest: device (GPS audio and navigation instructions) 2. Driver-to-Passenger Full Duplex Intercom Connection Lowest 3. MP3 Connectivity A high priority Audio Source will always interrupt any lower priority Audio Source. Mobile phone call overrides Intercom calls. AUDIO SOURCES AND PRIORITIES ­ Passenger Unit Passenger can also initiate intercom calls with drivers unit as well as listen to music from his MP3 Player. Intercom call overrides the audio from the MP3 player. Speaker B ATTACHING AND REMOVING THE HEADSET FROM THE HELMET CLAMP ATTACHING: Slide the headset downwards along the sliding panel until a clicking sound indicates that the headset is locked in place. 7 USING THE MP3 PLAYER WITH YOUR HEADSET Your SCALA RIDER headset can be connected to an MP3 player/audio device by simply plugging it to the Helmet Clamp's jack with the audio cable as follows: | SCALA RIDER® TeamSetTM 1. Power on the headset to have it on Standby mode, flashing slowly in Blue. Connect one side of the audio cable to your MP3 player/audio device's jack and the other side to the helmet Clamp's jack as shown in the photo. Operate the MP3 Player/audio device by using its buttons (FF / REW / PLAY / PAUSE ). INITIATING AND RECEIVING MOBILE PHONE CALLS Voice Recognition (VR) Connect the audio cable to the helmet Clamp's jack NOTE: Volume can only be adjusted through the MP3 Player. Any other audio connection will automatically mute the MP3 Player. The audio signal will return only when headset is once again in Standby mode. The VR feature allows you to answer or reject incoming calls by voice Control without having to remove your hands from the handlebars. [. . . ] Cardo will not be responsible for any physical damages, irrespective of reasons, conditions or circumstances, including malfunctioning of the Device, and all risks associated with operating it rest solely and entirely with the user of this Device, irrespective of whether the Device is used by the original purchaser or any third party. Cardo hereby notifies you that using this Device may also be in contravention to local, federal, state or national laws or regulations, and that any use of the Device is entirely at your sole risk and responsibility. You, your heirs, legal representatives, successors or assigns, hereby voluntarily and forever release, discharge, indemnify and hold harmless Cardo from any and all litigation, claims, debts, demands, actions and liability which may arise, directly or indirectly, from using the Device for any distress, pain, suffering, discomfort, loss, injury, death, damages to or in respect to any person or property however caused, WHETHER ARISING FROM THE NEGLIGENCE OR OTHERWISE, and which may hereafter accrue to you on some future date as a result of said use, to the fullest extent permitted by law. You fully understand and assume the risks in using the Device, including risk of negligent acts or omissions by others. [. . . ]