User manual CARDO SCALARIDER TEAMSET PRO

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual CARDO SCALARIDER TEAMSET PRO. We hope that this CARDO SCALARIDER TEAMSET PRO user guide will be useful to you.

Lastmanuals help download the user guide CARDO SCALARIDER TEAMSET PRO.


Mode d'emploi CARDO SCALARIDER TEAMSET PRO
Download
Manual abstract: user guide CARDO SCALARIDER TEAMSET PRO

Detailed instructions for use are in the User's Guide.

[. . . ] TM TeamSet PRO TM communication in motion TM User Guide Gebrauchsanleitung Guide d'Utilisation Guida di Avvio Guia de Usario © Cardo Systems, Inc. The Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc. Any use of such marks by Cardo Systems, Inc. Other trademarks and trade names are those of their respective owners. 2 scala rider® TeamSetTM PRO INTRODUCTION Congratulations and thank you for choosing the scala rider TeamSet pro Bluetooth® Headset package for bikers. [. . . ] You may need to reposition the Clamp repeatedly until you identify the best spot. The microphone must be positioned vertically and not horizontally (Be sure to clean the selected area prior to the gluing process). Use the pre-moistened Towelette to clean the helmet area where you want to install the Glue Plate. Peel the foil cover from the Glue Plates' adhesive pad. Place the Glue Plate into position according to #3. Press firmly 15 seconds on all 3 parts of the Glue Plate. The adhesive pad bonds to full strength over the next 24 hours. Therefore it is recommended to not use the headset during this 24 hour period. Fasten the Clamp to the Glue Plate using the Allen screws that were previously removed. Using two speakers inside the helmet may be prohibited in certain jurisdictions. If this is the case, you Cable should tuck away the long corded speaker underneath the helmet Speaker B padding as follows: Lead the speaker cord [B] alongside the rim of the padding to the right side and then back to Speaker B the left side, near speaker [A]. Then place the speaker [B] underneath the padding. English Speaker A POSITIONING THE SPEAKERS Attach the speakers to the Velcro inside your helmet opposite your ears (short speaker cord for the left ear [A] and the long speaker cord [B] for the right ear). You may want to use the supplied Velcro pad. Speaker A ATTACHING AND REMOVING THE HEADSET FROM THE HELMET CLAMP ATTACHING: Slide the headset downwards along the sliding panel until a clicking sound indicates that the headset is locked in place. REMOVING: Your headset can be removed for charging and storage by pressing your finger gently against the tab and sliding the headset up with the other hand. Please make sure to test the Intercom functionality in a LOUD environment, such as next to an idling motorcycle. Please also verify that the headsets were paired together properly by following the instructions in the relevant Setup sections. Terminate a call Voice Dial PHONE FUNCTIONS Tap the CTRL Button to end a call. During Standby, tap the CTRL Button and state the name of the person you wish to call. This feature is supported only by mobile phones that support the Voice Dial feature. Press and hold the Volume Down Button for three seconds during Standby. English Redial Enable/Disable Voice Connect feature (VOX) The scala rider TeamSet pro offers VOX technology for safe and hands-free operation of some key functions. For incoming calls, just pronounce loudly any word (e. g. To reject an incoming call, you need only to remain silent for about 15 seconds. To reject an intercom call remain silent for 30 seconds. While on standby press and hold the Volume Up and Volume Down Buttons simultaneously for three seconds until you hear a beep. [. . . ] End users must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. European CE Notice The scala rider TeamSetTM pro headset (the "Product") is in conformity with the following essential requirements of Council Directive 1999/5/EC (referred to as R&TTE Directive): Articles 3. 1a, 3. 1. b and 3. 2. The Product is manufactured in accordance with Annex II of the above directive. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE CARDO SCALARIDER TEAMSET PRO

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual CARDO SCALARIDER TEAMSET PRO will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag