User manual CARLSBRO TYTAN

[. . . ] To reduce the risk of fire or electric shock, do not expose the product to rain or moisture and do not place any objects filled with liquids, such as vases, on the product. g Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. h Do not remove the casing of this product. 2 EN Risk of overheating! [. . . ] •• Risk of explosion: Do not short circuit batteries. Do not expose batteries to excessive heat. Do not recharge non-rechargeable batteries. This product complies with the radio interference requirements of the European Community. This product is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. A copy of the EC Declaration of Conformity (DoC) is available in the packaging. Your product is designed and manufactured with high quality materials and components, which can be recycled and reused. When this crossed-out wheeled bin symbol is attached to a product it means that the product is covered by the European Directive 2002/96/ EC. Environmental information All unnecessary packaging has been omitted. We have tried to make the packaging easy to separate into three materials: cardboard (box), polystyrene foam (buffer) and polyethylene (bags, protective foam sheet. ) Your system consists of materials which can be recycled and reused if disassembled by a specialized company. Please observe the local regulations regarding the disposal of EN 3 English This product is fitted with an approved molded plug. If you replace the fuse, use one with: Please inform yourself about the local separate collection system for electrical and electronic products. Please act according to your local rules and do not dispose of your old products with your normal household waste. Correct disposal of your old product helps to prevent potential negative consequences for the environment and human health. packaging materials, exhausted batteries and old equipment. “Made for iPad” means that an electronic accessory has been designed to connect specifically to iPad, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. •• Before you connect the AC power cord, make sure that you have completed all the other connections. Install/replace microphone batteries Caution •• Risk of explosion!Keep batteries away from heat, •• Danger of explosion if batteries are incorrectly sunshine, or fire. Replace only with the same or equivalent type. •• Batteries contain chemical substances, so they should be disposed of properly. 1 Open the battery compartment and take out the battery cartridge. • Connect the AC power cord to • the AC MAINS~ socket on the back of the Bluetooth® speaker. • the wall power socket. Switch on the Bluetooth® speaker • Press on the top of the Bluetooth® speaker. »» The power indicator lights up white. To switch the unit to standby mode, press on the top panel. 2 Insert 3 x AAA batteries (supplied) into the cartridge with correct polarity (+/-) as indicated. • EN 7 English 3 Get started • To switch the unit on from standby mode, press again. 3 Push back the battery cartridge, then close the battery compartment. Note •• If you are not going to use the microphone for a long •• New batteries installed in the microphone support up •• When the power indicator flashes red, it indicates that the power level is low and you need to replace the batteries. time, remove the batteries. 8 EN Sing along through the wireless microphone Note •• The effective operation range between the wireless microphone and Bluetooth® speaker is approximately 10 meters (30 feet). 4 1 Dock your iPad onto the Bluetooth® speaker. »» A prompt pops up on the iPad screen, asking you to install the relevant app. Slide the OFF/ON switch on the wireless microphone to the ON position. »» The Bluetooth® indicator on the Bluetooth® speaker flashes blue. »» The wireless microphone starts to pair with the Bluetooth® speaker automatically. [. . . ] •• If you experience howling or echo, try to increase the distance between the microphone and speaker or adjust the angle of the microphone towards the speaker. 2 Enable Bluetooth® on your device that supports A2DP (Advanced Audio Distribution Profile). 10 EN 3 Select 'CARLSBRO_TYTAN/10' on your Bluetooth® enabled device and if necessary input '0000' as the paring password. »» After successful pairing and connection, the Bluetooth® indicator on the speaker turns solid blue and the speaker beeps twice. Play and charge your iPad through the dock connector directly Compatible iPad This unit supports play and charge of the following iPad models: • • • New iPad iPad 2 iPad Load the iPad • Dock your iPad. 4 Start music play on your Bluetooth® enabled device. To remove the iPad • Pull the iPad out of the dock. Listen to the iPad 1 5 Use -/+ on the top of the Bluetooth® speaker to adjust volume. Make sure that the iPad has been loaded correctly. »» The connected iPad starts to play. Use -/+ on the top of the Bluetooth® speaker to adjust volume. 2 3 EN 11 English Charge the iPad The docked iPad begins to charge as soon as the unit is connected to AC power. Play from an external device You can also listen to an external audio player through the Bluetooth® speaker. AUDIO-IN 1 Connect a 3. 5mm audio cable to: • the AUDIO-IN socket on the back of the Bluetooth® speaker. [. . . ]