User manual CARVIN C2440

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual CARVIN C2440. We hope that this CARVIN C2440 user guide will be useful to you.

Lastmanuals help download the user guide CARVIN C2440.


Mode d'emploi CARVIN C2440
Download
Manual abstract: user guide CARVIN C2440

Detailed instructions for use are in the User's Guide.

[. . . ] This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompa nying the appliance. LIMITED WARRANTY Your Carvin product is guaranteed against failure for 1 YEAR unless otherwise stated. Carvin will service and supply all parts at no charge to the customer providing the unit is under warranty. Shipping costs are the responsibility of the customer. CARVIN DOES NOT PAY FOR PARTS OR SERVICING OTHER THAN OUR OWN. [. . . ] CHANNEL MUTE SWITCH Mute a channel instantly without touching your faders. This is extremely useful when you need to mute channels but can't afford to lose fader settings. 14. CHANNEL PFL SWITCH This switch allows the operator to monitor each channel to set tone, gain and effect levels before turning up the fader 15. CHANNEL ASSIGNMENT SWITCHES These switches assign the channels' signal to the group faders for sub-mixing and to the Left & Right faders in the Master Section. Each channel can be assigned to the 12, 3-4, and L-R Faders in stereo pairs. This feature allows the operator to group certain channels (such as the channels used to mic an entire drum kit) and assign them to one pair of the master faders in the 1-2, 3-4 sub group. This sub-mixing feature decreases the number of channel faders that need to be adjusted. channel is great for a third main mix, a subwoofer out or in the case of a main mono mix, group 1-4 and L-R creates a 6 buss console. 28. PHONES JACK 1/4" stereo jack for headphone or control room output. 20. CONTROL ROOM SELECTION SWITCHES Use these switches to select what is heard through the headphones and control room jacks. Select LEFT-RIGHT, CENTER, GROUP 1-2 or GROUP 3-4 30. TAPE IN TO L-R SWITCH This switch assigns the source coming from the RCA TAPE IN connections to the L-R mix. 16. AUDIO TAPER FADERS Slide all faders down when connecting your inputs. Increase each channels fader to achieve the overall mix. Calibrated 60mm faders with audio taper are featured for smooth fade-outs. 21. PFL RED LED Indicates that the headphone, control room, and meters are monitoring the channels where the PFL is switched on. 31. TAPE IN CONTROL This adjusts the level of the source coming from TAPE IN. 32. CONTROL ROOM JACK This 1/4" stereo connection is for headphones or connecting a control room power amp & studio reference monitors. 22. L-R SUB TO CENTER SWITCHES Assignes the LEFT-RIGHT mix to the CENTER Fader. MASTER SECTION 17. GROUPS 1 - 4 Once a channel has been assigned to one of the 4 groups (see 15), 60mm faders control the level of each group. 23. PHONES CONTROL The PHONES control sets the desired level of the PHONES jack for monitoring through headphones. 41 40 39 38 37 33. TAPE OUT SOURCE This switch changes the tape out source from L-R to AUX 3-4. This is a great feature for 2 track live recording where a different mix is needed from the L-R house mix 34. [. . . ] This allows the send to be connected to the input of the external equipment and the return to its output completing the insert loop back to the channel. HALF INSERT DIRECT OUT The half insert connection creates a send sig nal without breaking the channels signal path. The insert in this mode is no longer used as an insert but it becomes what is called an "insert direct out". An insert direct out functions as a normal direct out but the plug has to be half inserted. If an insert is needed on the same channel, special cabling is required to perform both functions. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE CARVIN C2440

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual CARVIN C2440 will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag