User manual CASABLANCA FAN COMPAGNY FOURSEAS3

[. . . ] . OUR SEASONS III OWNERS MANUAL CONTENTS INTRODUCTION . 8 CONTROL FEATURES: 3-SPEED CONTROL WIRING . 14 READ AND SAVE THESE INSTRUCTIONS SAFETY FIRST Safety and the proper operation of your Casablanca fan both require a thorough knowledge of the product and proper installation; therefore, before attempting to install and operate your Casablanca fan, read this owner's manual completely and carefully. Retain this manual for future reference. [. . . ] This box must be secured to the ceiling according to the outlet box manufacturer's instructions. It is recommended that this be done by a qualified electrician. Vaulted or Cathedral Ceiling Installations Your Casablanca fan may be installed on a vaulted or cathedral ceiling in the same manner as described for a flat ceiling. The Hang-Tru® mounting system makes it possible to hang your fan on sloped ceilings up to a 32° angle. Using Existing Ceiling Fixture Outlet Box After turning electrical power off, lower the old fixture to expose the wiring and the ceiling fixture outlet box. Cut the fixture wires or if wire nuts have been used, unscrew them and disconnect the wires. After removing the old fixture, check the outlet box to sure that it is supported by a joist or beam across its upper surface. If not, a 2" x 4" stud must be installed. OUTSIDE USA - SECONDARY SUPPORT INSTALLATION PARTS OUTLET ADAPTOR PLATE 6" OUTLET BOX CABLE 3 /8"- 7 LAG SCREW (5") FENDER WASHER SPRING LOCK HOOK OUTSIDE USA - MOUNTING SECONDARY SUPPORT PARTS TO OUTLET BOX WARNING: MOUNT ONLY TO AN OUTLET BOX MARKED ACCEPTABLE FOR FAN SUPPORT ···· ADVERTISSEMENT: ASSEMBLER UNIQUEMENT À UNE BÔITE DE SORTIE JUGÉE ACCEPTABLE POUR RETENIR UN VENTILATEUR. Before beginning Step 1, follow Steps A-C on Page 3. Remove the knockout plug in the center of the outlet box or drill a 1/2" hole for the lag screw to pass through. Then drill a 1/4" guide hole into the joist or beam to a depth of 3 inches. Route the outlet box wires through the /2" diameter outer hole of the outlet adaptor plate. Line up the slotted holes and four canopy screw holes in the crossbar mounting bracket and outlet adaptor plate with the 8-32 mounting holes in the outlet box. Install the two 8-32 X 21/4" (1") screws and flat washers in fan hardware kit and tighten securely by hand only!With fender washer and outlet box cable attached as shown, pass lag screw through center hole of outlet adaptor plate and screw into pre drilled 1/4" guide hole of joist. Tighten until outlet box is firmly mounted. TIP: Threading two of the canopy screws into the crossbar mounting bracket will help everything stay aligned as you tighten the lag screw. 6" OUTLET BOX CABLE 1 JOIST OR BEAM 1 /4" GUIDE HOLE OUTLET BOX CROSSBAR MOUNTING BRACKET /2" HOLE 1 OUTLET ADAPTOR PLATE 8-32 X 21/4" (1") SCREW LAG SCREW FENDER WASHER 8 FOUR SEASONSTM III (OUTSIDE USA INSTALLATION) OUTSIDE USA - SECONDARY SUPPORT o PREPARING THE SWITCH HOUSING Step 5. Hold the switch housing close to the fan and connect the motor plug to the switch housing socket. The connectors are keyed to ensure correct alignment during installation - Do not force!Locate the blue and white LIGHT wires in the switch housing. Check the tightness of the Cable Clamp & Screw. (The clamp should not slip along the cable. ) Step 8. [. . . ] A vacuum cleaner brush nozzle can remove heavier dust. Surface smudges or an accumulation of dirt and dust can easily be removed by using a mild detergent and slightly dampened soft cloth. An antistatic agent may be used, but never use abrasive cleaning agents. Painted and high-gloss blades may be cleaned in the same manner. [. . . ]