User manual CASABLANCA FAN COMPAGNY NOUVELLE

[. . . ] NOUVELLE OWNERS MANUAL CONTENTS INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 MOUNTING RECOMMENDATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 FAN INSTALLATION - GETTING STARTED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 ADAPTOR PLATE INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 FAN PREPARATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 INSTALLATION & WIRING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 LIGHT FIXTURE INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Install three finger screws into each light fitter. Position the shade fully in the fitter and tighten each finger screw two turns each in rotation until the shade is centered in the fitter. Check that the shade is captured by the finger screws by lightly pulling on the shade. Hand tighten the finger screws securely. Replace bulbs only with the exact type and wattage. Note: Check the finger screws periodically as they will loosen and cause operating noise. FOR OPERATIONAL CONTROLS, PLEASE SEE PAGE 12. FINGER SCREW (3 PER SHADE) NO LIGHT FIXTURE OPTION - FIXTURE REMOVAL Step 19. Remove the locknut securing the light fixture to the lower switch housing. Save locknut and fixture for future use. LOCKNUT LOWER SWITCH HOUSING LIGHT FIXTURE 10 NOUVELLETM NO LIGHT FIXTURE OPTION - HARDWARE LOWER SWITCH HOUSING CAP THREADED BUTTON NO LIGHT FIXTURE OPTION - HARDWARE ASSEMBLY Step 20. Line up the center holes of the cap and lower switch housing to allow the threaded button to be installed. Hand tighten securely LOWER SWITCH HOUSING LOWER SWITCH HOUSING CAP THREADED BUTTON NO LIGHT FIXTURE OPTION - INSTALLATION HARDWARE LIGHT FIXTURE SCREW PHILLIPS COUNTERSUNK 6-32 X 5/16 (3) NO LIGHT FIXTURE OPTION - INSTALLATION Step 21. Align the three holes in the side of the fixture with the three threaded holes in the adaptor ring and install the three (3) 6-32 X 5/16 Phillips screws. Hand tighten securely. LIGHT FIXTURE SCREW 11 R INTELI·TOUCH© INSTALLING THE W-32 WALL CONTROL The wall control installs in the same manner as an ordinary light switch, using an existing junction box and wiring. This controller is designed to signal the fan microcomputer as well as perform normal switching operations. For this reason the following precautions must be observed: 1. Use only the Casablanca W-32 wall control. Do not use more than one fan per wall control. Do not use any additional control with your Inteli-Touch 4. No other light fixtures or electrical appliances may be confan (for example, dimmer, fan speed control, etc. ). nected on the circuit controlled by the W-32 wall control. INTELI·TOUCH o SINGLE W-32 INSTALLATION CAUTION!Ensure power is turned OFF at the breaker or fuse panel before starting installation. W-32 is used to describe either white (-11) or ivory finish. [. . . ] You may increase the fan speed by pressing and holding the button until the desired speed is reached, then release it. The fan will again reduce one speed for each 2 hour interval. 14 R TROUBLESHOOTING Before Requesting Service: Please follow this troubleshooting guide before contacting your dealer for assistance. Caring for Finishes: For cleaning, a soft brush or lint-free cloth should be used to prevent scratching the finish. A vacuum cleaner brush nozzle can remove heavier dust. Surface smudges or an accumulation of dirt and dust can easily be removed by using a mild detergent and slightly dampened soft cloth. [. . . ]