User manual CASABLANCA FAN COMPAGNY S3

[. . . ] S3 OWNERS MANUAL CONTENTS INTRODUCTION . 3 CONTROL FEATURES: VERSA·TOUCH OPERATION . 10 READ AND SAVE THESE INSTRUCTIONS SAFETY FIRST Safety and the proper operation of your Casablanca fan both require a thorough knowledge of the product and proper installation; therefore, before attempting to install and operate your Casablanca fan, read this owner's manual completely and carefully. Retain this manual for future reference. [. . . ] Rotate the fan body until the slot in the nylon ball fits into the pin opposite the canopy opening. BALL NOTE: The fan weight is 23 pounds. PIN SLOT CANOPY ELECTRICAL CONNECTIONS Step 5a. Attach the fan wires to the ceiling fixture outlet box wiring by twisting the bare ends of the wires together and then securing with a wire nut. Test that the connection is secure by pulling on the wire nut. Wiring Connections · GREEN leads from mounting plate and fan to GROUND conductor of power source. · WHITE wire from fan to white NEUTRAL wire in ceiling fixture outlet box. · BLACK power wire from fan to BLACK power wire in ceiling outlet box. Secure with wire nut. 2 BLACK WIRES 2 WHITE WIRES WIRE NUT 3 GREEN WIRES CANOPY HATCH INSTALLATION Step 6. Tuck the wires into the canopy with the wire nuts pointed upwards, so that the WHITE and BLACK wires are on opposite sides of the canopy and all wires are clear of the canopy opening. Install canopy hatch with the last canopy screw and lock washer. To do this, tilt the fan body away from the hatch opening. Tighten the screws firmly by hand only, Step 8. Straighten the fan, then check to ensure that there is no movement between the canopy and ceiling or Hang-Tru ball and top support shaft. CANOPY HATCH LOCK WASHER CANOPY SCREW TILT THE FAN TO INSTALL LAST CANOPY SCREW 6 6 S3TM INSTALL BULB AND GLASS Step 9. Screw the 100 Watt Halogen bulb into the socket. Do not touch the glass bulb with your fingers­it is extremely important that the glass be clean. If it is touched, or dirty, clean carefully with a tissue. A dirty glass bulb will cause the bulb to fail almost immediately. When installing the halogen bulb, carefully cut off the end of the plastic sleeve the bulb comes in and hold the bulb by the plastic sleeve to screw it into the socket. TABS HALOGEN BULB 100 WATT Step 10. Position the indentations in the outer rim of the glass shade so that they line up with the tabs on the inside surface of the fan light fixture rim. Carefully lift the glass shade up inside the light fixture as far as it will go. Install and tighten screws by hand only. Note: The wall anchors and 6-32 x 1" screws may be used in situations where mounting to a stud is not possible. After securing the anchor, discard the anchor's pointed screws and use the 6-32 decor ovalhead screws supplied. ANCHOR PANHEAD SCREW Control Storage Angle control in top first in the holder until the unit can be gently pushed back and snapped onto the bottom rim. TOP GOES IN FIRST DRYWALL ANCHOR WOOD SCREW 1" DECOR OVALHEAD SCREW 6-32 X 1" Removing Gently Pull the lower edge of the control gently out from the holder. VERSA·TOUCH o BATTERY INSTALLATION Remove Battery Door Turn control on its front. [. . . ] ·Check the frequency setting: Turn power off, at the circuit breaker, only for the fan not functioning for at least 5 seconds; turn the power back on; within 20 seconds press the Hi, Med, and Lo buttons (in that order) to set the frequency of the fan to the control. See Page 9. FAN WOBBLES OR SHAKES ·Be sure canopy pin is properly set into the slot on the ball. EXCESSIVELY ·Check that bladeholders have not been bent during installation and blades are balanced. ·Hanger bracket and/or ceiling outlet are loosely attached: Make sure that the hanger bracket is tightly attached to the ceiling outlet box. [. . . ]