User manual CASABLANCA FAN COMPAGNY WAILEA

[. . . ] The maximum current requirement for the fan with light fixture is 3. 8 amps. Maximum light current is 2. 8 amps or 340 watts of lighting. · Where wire nuts are employed, be sure all bare wires are within the connectors. When installing the canopy hatch, make sure all wires are within the canopy and that no wires are being pinched. [. . . ] Thread the downrod into the motor coupling until it stops turning, this will take at least four and a half full turns. Securely tighten the set screw with the provided allen wrench to ensure safe operation of your fan. CAUTION: Failure to fully lock in the downrod before securely tightening the allen set screw may cause the fan to separate from the downrod during normal operation! GROUND WIRE DOWNROD & BALL ASSEMBLY ALLEN SET SCREW TAPERED THREAD MOTOR COUPLING 3 WAILEA CROSSBAR MOUNTING BRACKET TM CEILING HARDWARE ADDITIONAL HARDWARE WIRE NUT (4) 21/4 x 8-32 ROUNDED HEAD SCREW (2) 1 x 8-32 ROUNDED FLAT WASHER (2) HEAD SCREW (2) GETTING STARTED Installing a New Ceiling Fixture Outlet Box If you do not have an existing fixture located where you wish to place your Casablanca fan, an approved ceiling fixture outlet box must be installed and wired. Warning:Toreducetheriskof fire, electricalshock, or personal injury, mount to outlet box marked acceptableforceilingfansupportusingthemounting hardware provided with the outlet box. Using Existing Ceiling Fixture Outlet Box After turning the power OFF at its source (either circuit breaker or fuse box), lower the old fixture and disconnect the wiring. Check the ceiling fixture outlet box to be sure that it is marked `Approved for ceiling fan mounting'. If it is not, a new box must be installed. CROSSBAR MOUNTING BRACKET INSTALLATION WARNING: Damp Location rated fans require a Ground Fault Interrupter (GFI). Use a weather-proof outlet box, properly connect ground wires, and use only under a weather-proof structure. CEILING FAN APPROVED OUTLET BOX Proceed with installation as follows: Step 1. Route the wires from the ceiling outlet box through the crossbar mounting bracket center hole. Attach the bracket, with ground wire and ridges down, to the ceiling fixture outlet box with the mounting hardware included with the outlet box. Using the screwdriver, tighten the screws firmly by hand only, being careful not to bend the bracket by over tightening. CEILING WIRING CROSSBAR MOUNTING BRACKET FLAT WASHER RIDGE SIDE DOWN CAUTION: To reduce the risk of personal injury, use only the mounting hardware provided with the approved outlet box to install the crossbar mounting bracket. GREEN GROUND WIRE OUTLET BOX MOUNTING HARDWARE CANOPY HARDWARE CANOPY SCREW (4) CANOPY HATCH CANOPY CANOPY LOCK WASHER (4) 4 WAILEA CANOPY INSTALLATION Step 2. Thread the wires from the ceiling through the opening in the canopy. Attach the canopy to the crossbar mounting bracket with three of the 8-32 x 21/4 long canopy screws and canopy lock washers. Using the screwdriver, tighten the screw firmly by hand only. Note: On sloped ceilings, align the canopy opening toward the top or room peak. CROSSBAR MOUNTING BRACKET INSTALLED TM CANOPY CANOPY LOCK WASHERS CANOPY SCREWS HANGING THE FAN Step 3. To hang the fan body in the canopy, hold the fan body firmly and insert the ball into the canopy opening. Rotate the fan body until the slot in the ball fits into the pin opposite the canopy opening. Note: The fan weight is 11 lbs. CAPPED BLUE D1-OPTION WIRE. BALL SLOT PIN CANOPY ELECTRICAL CONNECTIONS Step 4a. Attach the fan wires to the ceiling fixture outlet box wiring by placing the bare ends of the wires side by side and then securing with a wire nut. Test that the connection is secure by pulling on the wire nut. Pull Chain Connections · GREEN leads from mounting plate and fan to GROUND conductor of power source. · WHITE wire from fan to white NEUTRAL wire in ceiling fixture outlet box. [. . . ] Check that bladeholders have not been bent during installation. Check and tighten light fixture retaining screws, glass shade screws and/or the light bulb(s) as neccessary. Tighten the blade to bladeholder screws. Tighten canopy screws and mounting plate assembly. [. . . ]