User manual CASIO AT-3 appendix

[. . . ] However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. [. . . ] Perform the procedure under "To start a song editor operation" on page E-76 to display the song editor menu. 1. Perform the procedure under "To start a song editor operation" on page E-76 to display the song editor menu. 2. Use the R-17 (t, y) buttons to move the 0 to "DeleteMeas. " and then press the R-16 (ENTER) button. · This causes "Delete Measure" screen to appear. At this time the thick brackets (%) will be located at the "Measure" setting. 2. Use the R-17 (t, y) buttons to move the 0 to "InsertMeas. " and then press the R-16 (ENTER) button. · This causes "Insert Measure" screen to appear. At this time the thick brackets (%) will be located at the "Measure" setting. 3. Use the dial or R-14 (­, +) buttons to specify the song measure you want to delete. 3. Use the dial or R-14 (­, +) buttons to specify the song measure number from which you want the insert to start. 4. Press the R-17 (y) button to move the thick brackets (%) to "Size". 4. Press the R-17 (y) button to move the thick brackets (%) to "Size". 5. Use the dial or R-14 (­, +) buttons to specify the number of measures you want to insert. · For example, specifying 002 for "Measure" and 003 for "Size" will insert three blank measures in front of song measure 2. 6. Use the R-17 (t, y) buttons to move the 0 to "TrackEdit" and then press the R-16 (ENTER) button. · This displays the track editor menu shown below. 3. Use the dial or R-17 (u, i) buttons to specify the track you want to clear. · A black box ( ) above a track number in the level meter indicates that there is already data recorded in that track. · You also can select a track using the dial or R-14 (­, +) buttons. 4. In response to the "Sure?" message that appears, press the R-14 (YES) button to clear or the R-14 (NO) button to cancel. E-80 Using the Song Sequencer To copy one track to another track (Tracks 01 through 16 only) To combine two tracks into a single track (Tracks 01 through 16 only) 1. Perform the procedure under "To start a track editor operation" on page E-80 to display the track editor menu. 1. In the song sequencer mode, use the R-17 (u, i) buttons to select the lower numbered track of those you want to combine. · As an example, we will combine Track 03 and Track 05 into Track 06. Use the R-17 (t, y) buttons to move the 0 to "Copy" and then press the R-16 (ENTER) button. · This causes the "Copy Track" screen to appear. At this time the thick brackets (%) will be located at the "Copy" setting. 2. Perform steps 2 and 3 of the procedure under "To start a track editor operation" on page E-80 to display the track editor menu. 3. Use the dial or R-14 (­, +) buttons to specify the track number you want to copy from. 3. Use the R-17 (y) button to move the 0 to "Merge" and then press the R-16 (ENTER) button. · This displays a "Merge Track" screen like the one shown below. [. . . ] 4 :Noise2 Level (0, 1, 2, 3, 4, 5) Adjusts the level of Noise Generator 2. 5 :Noise2 Density (0, 1, 2, 3, 4, 5) Adjusts the frequency of Noise Generator 2. A larger number produces greater distortion. Raising the noise level while a note is not sounding will cause noise to sound, even if there is no input signal. Dual Type DSP Parameters Dual type DSPs are configured by combining two different single type DSPs. [. . . ]