User manual CASIO AT-5

[. . . ] E USER'S GUIDE Please keep all information for future reference. Safety Precautions Before trying to use the keyboard, be sure to read the separate "Safety Precautions". AT3/AT5-E-1B NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ] In response to the "Sure?" message that appears, press the R-14 (YES) button to insert or the R-14 (NO) button to cancel. 6. After everything is the way you want, press the R-16 (ENTER) button. 7. In response to the "Sure?" message that appears, press the R-14 (YES) button to delete or the R-14 (NO) button to cancel. E-78 Using the Song Sequencer To extract system track recorded content to track 04 through 07 or 09 through 16 As explained in detail under "Songs, tracks, and parts" (page E-65), the system track is an individual track, while the keyboard play and Auto Accompaniment data are recorded individually to multiple parts (A04 through A07, A09 through A16). The data of these parts is extracted to Tracks 04 through 07 and 09 through 16, with one part corresponding individually to one track of data. This makes it easy to edit each accompaniment part individually. A04 A05 A06 A07 A09 A10 A11 A12 A13 A14 A15 A16 B04 B05 B06 B07 B09 B10 B11 B12 B13 B14 B15 B16 To rename a song 1. Perform the procedure under "To start a song editor operation" on page E-76 to display the song editor menu. 2. Use the R-17 (y) button to move the 0 to "Rename" and then press the R-16 (ENTER) button. · This displays the "Rename" screen. Syste Track 3. Use the R-17 (u, i) buttons to move the cursor to the name character position you want to change, and then use the dial or R-14 (­, +) buttons to select the character you want. · See "Supported Input Characters" (page E-155) for information about the characters you can input for the name. · To input a space, press both of the R-14 (­, +) buttons at the same time. · Performing this operation will delete all data currently recorded in the system track except for tempo data. · Performing this operation deletes all data currently recorded in Tracks 04 through 07 and 09 through 16, and overwrites it with the data in the system track. 1. Perform the procedure under "To start a song editor operation" on page E-76 to display the song editor menu. 4. After everything is the way you want, press the R-16 (ENTER) button. 2. Use the R-17 (t, y) buttons to move the 0 to "Extract" and then press the R-16 (ENTER) button. · This displays an "Extract" screen like the one shown below. 5. In response to the "Sure?" message that appears, press the R-14 (YES) button to rename the song or the R-14 (NO) button to cancel. 3. In response to the "Sure?" message that appears, press the R-14 (YES) button to start extraction or the R-14 (NO) button to cancel. E-79 Using the Song Sequencer Editing a Track The following operations are supported during track (system track, Tracks 01 through 16) editing. · Clearing a single track · Copying one track to another track (Tracks 01 through 16 only) · Combining two tracks into a single track (Tracks 01 through 16 only) To clear a single track 1. Perform the procedure under "To start a track editor operation" on page E-80 to display the track editor menu. 2. Press the R-16 (ENTER) button. · This causes the "Clear Track" screen to appear. To start a track editor operation 1. Press the C-5 (SONG SEQUENCER) button to enter the song sequencer mode. 2. While holding down the R-13 (FUNCTION) button, press the C-5 (EDIT) button to display the edit menu. 3. Use the R-17 (t, y) buttons to move the 0 to "TrackEdit" and then press the R-16 (ENTER) button. · This displays the track editor menu shown below. 3. Use the dial or R-17 (u, i) buttons to specify the track you want to clear. · A black box ( ) above a track number in the level meter indicates that there is already data recorded in that track. [. . . ] Use the procedure below to determine what parameters that can be configured for each dual type DSP, and the operation, and setting ranges of dual type DSPs. Example: Type number 29: Distortion-Wah 1. The DSP type name has two parts: a left side part and a right side part. Distortion-Wah 3 "Distortion" and "Wah" 2. [. . . ]